diff options
Diffstat (limited to 'mk/dirdeps.mk')
| -rw-r--r-- | mk/dirdeps.mk | 24 |
1 files changed, 16 insertions, 8 deletions
diff --git a/mk/dirdeps.mk b/mk/dirdeps.mk index 3335fdb0943ad..8c342be86fc25 100644 --- a/mk/dirdeps.mk +++ b/mk/dirdeps.mk @@ -1,4 +1,4 @@ -# $Id: dirdeps.mk,v 1.29 2013/10/13 18:43:53 sjg Exp $ +# $Id: dirdeps.mk,v 1.35 2014/05/03 06:27:56 sjg Exp $ # Copyright (c) 2010-2013, Juniper Networks, Inc. # All rights reserved. @@ -44,7 +44,7 @@ # All unqualified entries end up being qualified with .${TARGET_SPEC} # and partially qualified (if TARGET_SPEC_VARS has multiple # entries) are also expanded to a full .<target_spec>. -# The _DIRDEPS_USE target uses the suffix to set TARGET_SPEC +# The _DIRDEP_USE target uses the suffix to set TARGET_SPEC # correctly when visiting each entry. # # The fully qualified directory entries are used to construct a @@ -71,7 +71,7 @@ # # TARGET_SPEC_VARS # The default value is just MACHINE, and for most environments -# this is sufficient. The _DIRDEPS_USE target actually sets +# this is sufficient. The _DIRDEP_USE target actually sets # both MACHINE and TARGET_SPEC to the suffix of the current # target so that in the general case TARGET_SPEC can be ignored. # @@ -196,7 +196,11 @@ N_notmachine := ${.MAKE.DEPENDFILE_PREFERENCE:E:N*${MACHINE}*:${M_ListToSkip}} # if we were included recursively _DEP_TARGET_SPEC should be valid. .if empty(_DEP_TARGET_SPEC) # we may or may not have included a dependfile yet +.if defined(.INCLUDEDFROMFILE) +_last_dependfile := ${.INCLUDEDFROMFILE:M${.MAKE.DEPENDFILE_PREFIX}*} +.else _last_dependfile := ${.MAKE.MAKEFILES:M*/${.MAKE.DEPENDFILE_PREFIX}*:[-1]} +.endif .if !empty(_debug_reldir) .info ${DEP_RELDIR}.${DEP_TARGET_SPEC}: _last_dependfile='${_last_dependfile}' .endif @@ -239,7 +243,8 @@ DEP_MACHINE := ${_DEP_TARGET_SPEC} # we can use this as a clue to do initialization and other one time things. .if !target(_DIRDEP_USE) # make sure this target exists -dirdeps: +dirdeps: beforedirdeps .WAIT +beforedirdeps: # We normally expect to be included by Makefile.depend.* # which sets the DEP_* macros below. @@ -269,12 +274,15 @@ DEP_SKIP_DIR = ${SKIP_DIR} \ NSkipDir = ${DEP_SKIP_DIR:${M_ListToSkip}} -.if defined(NO_DIRDEPS) || defined(NODIRDEPS) +.if defined(NO_DIRDEPS) || defined(NODIRDEPS) || defined(WITHOUT_DIRDEPS) # confine ourselves to the original dir DIRDEPS_FILTER += M${_DEP_RELDIR}* .endif -# we supress SUBDIR when visiting the leaves +# this is what we run below +DIRDEP_MAKE?= ${.MAKE} + +# we suppress SUBDIR when visiting the leaves # we assume sys.mk will set MACHINE_ARCH # you can add extras to DIRDEP_USE_ENV # if there is no makefile in the target directory, we skip it. @@ -285,7 +293,7 @@ _DIRDEP_USE: .USE .MAKE MACHINE_ARCH= NO_SUBDIR=1 ${DIRDEP_USE_ENV} \ TARGET_SPEC=${.TARGET:E} \ MACHINE=${.TARGET:E} \ - ${.MAKE} -C ${.TARGET:R} || exit 1; \ + ${DIRDEP_MAKE} -C ${.TARGET:R} || exit 1; \ break; \ done @@ -397,7 +405,7 @@ DEP_DIRDEPS_FILTER = U .endif # this is what we start with -__depdirs := ${DIRDEPS:${NSkipDir}:${DEP_DIRDEPS_FILTER:ts:}:O:u:@d@${SRCTOP}/$d@} +__depdirs := ${DIRDEPS:${NSkipDir}:${DEP_DIRDEPS_FILTER:ts:}:C,//+,/,g:O:u:@d@${SRCTOP}/$d@} # some entries may be qualified with .<machine> # the :M*/*/*.* just tries to limit the dirs we check to likely ones. |