diff options
Diffstat (limited to 'Bindings/spi/spi-orion.txt')
| -rw-r--r-- | Bindings/spi/spi-orion.txt | 49 |
1 files changed, 48 insertions, 1 deletions
diff --git a/Bindings/spi/spi-orion.txt b/Bindings/spi/spi-orion.txt index 98bc69815eb3..4f629cc7634a 100644 --- a/Bindings/spi/spi-orion.txt +++ b/Bindings/spi/spi-orion.txt @@ -8,7 +8,15 @@ Required properties: - "marvell,armada-380-spi", for the Armada 38x SoCs - "marvell,armada-390-spi", for the Armada 39x SoCs - "marvell,armada-xp-spi", for the Armada XP SoCs -- reg : offset and length of the register set for the device +- reg : offset and length of the register set for the device. + This property can optionally have additional entries to configure + the SPI direct access mode that some of the Marvell SoCs support + additionally to the normal indirect access (PIO) mode. The values + for the MBus "target" and "attribute" are defined in the Marvell + SoC "Functional Specifications" Manual in the chapter "Marvell + Core Processor Address Decoding". + The eight register sets following the control registers refer to + chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. Optional properties: - interrupts : Is currently not used. @@ -23,3 +31,42 @@ Example: interrupts = <23>; status = "disabled"; }; + +Example with SPI direct mode support (optionally): + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */ + <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */ + <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */ + <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */ + <MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */ + <MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */ + <MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */ + <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */ + <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */ + interrupts = <23>; + status = "disabled"; + }; + +To enable the direct mode, the board specific 'ranges' property in the +'soc' node needs to add the entries for the desired SPI controllers +and its chip-selects that are used in the direct mode instead of PIO +mode. Here an example for this (SPI controller 0, device 1 and SPI +controller 1, device 2 are used in direct mode. All other SPI device +are used in the default indirect (PIO) mode): + soc { + /* + * Enable the SPI direct access by configuring an entry + * here in the board-specific ranges property + */ + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>, /* internal regs */ + <MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>, /* BootROM */ + <MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>, /* SPI0-DEV1 */ + <MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>; /* SPI1-DEV2 */ + +For further information on the MBus bindings, please see the MBus +DT documentation: +Documentation/devicetree/bindings/bus/mvebu-mbus.txt |