src/sys/modules/ath, branch releng/8.1FreeBSD source treehttps://cgit-dev.freebsd.org/src/atom?h=releng%2F8.12010-03-03T20:28:35ZAdd ah_eeprom_v4k.c2010-03-03T20:28:35ZRui Paulorpaulo@FreeBSD.org2010-03-03T20:28:35Zurn:sha1:ae266114fbd693e8f6ee5d0e34446f67bdab3c15Add ar9280.c and ar9280_attach.c.2010-03-03T20:08:12ZRui Paulorpaulo@FreeBSD.org2010-03-03T20:08:12Zurn:sha1:8004f2b3536d805449cdc4eba575c7d5aed0c521MFC 204656:2010-03-03T20:06:50ZRui Paulorpaulo@FreeBSD.org2010-03-03T20:06:50Zurn:sha1:fe0da2ff6e6139b14eccb9ee6cae2f0e18128c9b
Add missing ar9285_reset.c file.
MFC r197948 r203156 r203158 r203159 r203680 r203682 r203750 r203882 r2039302010-03-02T13:13:12ZRui Paulorpaulo@FreeBSD.org2010-03-02T13:13:12Zurn:sha1:2d057e0f6a593a9f64c23fb70498265227f025cb
r203933 r203959 r204521 r204578:
Atheros AR9285 support.
Remove ATH_SUPPORT_TDMA and use IEEE80211_SUPPORT_TDMA instead. It2009-03-30T19:23:49ZSam Lefflersam@FreeBSD.org2009-03-30T19:23:49Zurn:sha1:584f7327f1b6e4e227f4601423dfebd48e110e23
doesn't make much sense to configure driver support w/o net80211.
Note this means ath now depends on opt_wlan.h.
Combine ath rate control modules with ath after bringing ath_hal2008-12-14T22:26:57ZSam Lefflersam@FreeBSD.org2008-12-14T22:26:57Zurn:sha1:2a8d8e7cfdc93584c66c02f02b940ab3f67694fe
src into the tree. The old split was balanced on module dependencies
and symbol exposure that no longer exists. Users that want a module
setup with rate control algorithm other than sample must override
ATH_RATE in the ath module Makefile.
Reviewed by: imp
Rather than using hidden includes (with cicular dependencies),2008-12-02T21:37:28ZBjoern A. Zeebbz@FreeBSD.org2008-12-02T21:37:28Zurn:sha1:4b79449e2fb67cb37c4c9f46d31791893a39ddd8
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
Switch to ath hal source code. Note this removes the ath_hal2008-12-01T16:53:01ZSam Lefflersam@FreeBSD.org2008-12-01T16:53:01Zurn:sha1:33644623554bb0fc57ed3c7d874193a498679b22
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
for newer hal's we need opt_ah.h as it specifies how the hal has been2007-01-28T04:38:35ZSam Lefflersam@FreeBSD.org2007-01-28T04:38:35Zurn:sha1:9c0511629796d2030a83bca12ed6b49e778e0495
configured and that in turn controls the descriptor layout
o move ath hal os glue code from the hal to the driver: this code was2006-09-18T16:49:15ZSam Lefflersam@FreeBSD.org2006-09-18T16:49:15Zurn:sha1:3fe92528afe8313fecf48822dde74bad5e380f48
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks