// SPDX-License-Identifier: GPL-2.0
#include "qcom-msm8974pro.dtsi"
#include "pm8841.dtsi"
#include "pm8941.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
/ {
model = "OnePlus One";
compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
chassis-type = "handset";
qcom,msm-id = <194 0x10000>;
qcom,board-id = <8 0>;
aliases {
serial0 = &blsp1_uart2;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
pinctrl-names = "default";
key-volume-down {
label = "Volume Down";
gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEDOWN>;
wakeup-source;
debounce-interval = <15>;
};
key-volume-up {
label = "Volume Up";
gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
wakeup-source;
debounce-interval = <15>;
};
event-hall-sensor {
label = "Hall Effect Sensor";
gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
linux,input-type = <EV_SW>;
linux,code = <SW_LID>;
linux,can-disable;
debounce-interval = <150>;
};
};
vreg_boost: vreg-boost {
compatible = "regulator-fixed";
regulator-name = "vreg-boost";
regulator-min-microvolt = <3150000>;
regulator-max-microvolt = <3150000>;
regulator-always-on;
regulator-boot-on;
gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&boost_bypass_n_pin>;
};
vreg_vph_pwr: vreg-vph-pwr {
compatible = "regulator-fixed";
regulator-name = "vph-pwr";
regulator-min-microvolt = <3600000>;
regulator-max-microvolt = <3600000>;
regulator-always-on;
};
};
&blsp1_i2c1 {
status = "okay";
fuel-gauge@55 {
compatible = "ti,bq27541";
reg = <0x55>;
power-supplies = <&bq24196_charger>;
};
};
&blsp1_i2c2 {
status = "okay";
rmi4-i2c-dev@20 {
compatible = "syna,rmi4-i2c";
reg = <0x20>;
syna,startup-delay-ms = <100>;
interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8941_l22>;
vio-supply = <&pm8941_lvs3>;
pinctrl-names = "default";
pinctrl-0 = <&touch_default_state>;
#address-cells = <1>;
#size-cells = <0>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>;
};
rmi4-f12@12 {
reg = <0x12>;
syna,sensor-type = <1>;
/*
* Touchscreen size is 2040x1080, y-values between
* 1920-2040 are used for touchkey (menu, home & back).
* For now clip it off so we don't get touch events
* outside of the display area.
*/
syna,clip-y-high = <1920>;
};
};
led-controller@36 {
compatible = "ti,lm3630a";
reg = <0x36>;
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
led-sources = <0 1>;
label = "lcd-backlight";
default-brightness = <80>;
};
};
led-controller@68 {
compatible = "si-en,sn3193";
reg = <0x68>;
shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
led@1 {
reg = <1>;
label = "red:status";
led-max-microamp = <17500>;
};
led@2 {
reg = <2>;
label = "green:status";
led-max-microamp = <17500>;
};
led@3 {
reg = <3>;
label = "blue:status";
led-max-microamp = <17500>;
};
};
};
&blsp1_i2c6 {
status = "okay";
bq24196_charger: charger@6b {
compatible = "ti,bq24196";
reg = <0x6b>;
interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
omit-battery-class;
};
};
&blsp1_uart2 {
status = "okay";
};
&gcc {
compatible = "qcom,gcc-msm8974pro-ac";
};
&pm8941_coincell {
qcom,rset-ohms = <800>;
qcom,vset-millivolts = <3200>;
status = "okay";
};
&pm8941_gpios {
gpio_keys_default: gpio-keys-active-state {
pins = "gpio2", "gpio5";
function = "normal";
input-enable;
bias-disable;
power-source = <PM8941_GPIO_S3>;
};
};
&pm8941_vib {
status = "okay";
};
&pronto {
vddmx-supply = <&pm8841_s1>;
vddcx-supply = <&pm8841_s2>;
vddpx-supply = <&pm8941_s3>;
pinctrl-names = "default";
pinctrl-0 = <&wcnss_pin_a>;
status = "okay";
iris {
vddxo-supply = <&pm8941_l6>;
vddrfa-supply = <&pm8941_l11>;
vddpa-supply = <&pm8941_l19>;
vdddig-supply = <&pm8941_s3>;
};
smd-edge {
qcom,remote-pid = <4>;
label = "pronto";
wcnss {
status = "okay";
};
};
};
&remoteproc_adsp {
cx-supply = <&pm8841_s2>;
status = "okay";
};
&rpm_requests {
regulators-0 {
compatible = "qcom,rpm-pm8841-regulators";
pm8841_s1: s1 {
regulator-min-microvolt = <675000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s2: s2 {
regulator-min-microvolt = <875000>;
regulator-max-microvolt = <1050000>;
regulator-always-on;
};
pm8841_s3: s3 {
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
};
};
regulators-1 {
compatible = "qcom,rpm-pm8941-regulators";
vdd_l1_l3-supply = <&pm8941_s1>;
vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
vdd_l4_l11-supply = <&pm8941_s1>;
vdd_l5_l7-supply = <&pm8941_s2>;
vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
vdd_l21-supply = <&vreg_boost>;
pm8941_s1: s1 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_s2: s2 {
regulator-min-microvolt = <2150000>;
regulator-max-microvolt = <2150000>;
regulator-boot-on;
};
pm8941_s3: s3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-system-load = <154000>;
regulator-always-on;
regulator-boot-on;
regulator-allow-set-load;
};
pm8941_l1: l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_l2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
pm8941_l3: l3 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
pm8941_l4: l4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
pm8941_l5: l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l6: l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
pm8941_l7: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
pm8941_l8: l8 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l9: l9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
pm8941_l10: l10 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
pm8941_l11: l11 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1350000>;
};
pm8941_l12: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
regulator-allow-set-load;
};
pm8941_l13: l13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
pm8941_l14: l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l15: l15 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
pm8941_l16: l16 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8941_l17: l17 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
pm8941_l18: l18 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
pm8941_l19: l19 {
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <3350000>;
};
pm8941_l20: l20 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-system-load = <200000>;
regulator-allow-set-load;
regulator-boot-on;
};
pm8941_l21: l21 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
pm8941_l22: l22 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-allow-set-load;
};
pm8941_l23: l23 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
pm8941_l24: l24 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
regulator-boot-on;
};
pm8941_lvs3: lvs3 {};
};
};
&sdhc_1 {
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_on>;
pinctrl-1 = <&sdc1_off>;
status = "okay";
};
&smbb {
status = "okay";
};
&tlmm {
gpio_hall_sensor_default: gpio-hall-sensor-default-state {
pins = "gpio68";
function = "gpio";
drive-strength = <8>;
bias-pull-up;
};
sdc1_on: sdc1-on-state {
clk-pins {
pins = "sdc1_clk";
drive-strength = <4>;
bias-disable;
};
cmd-data-pins {
pins = "sdc1_cmd", "sdc1_data";
drive-strength = <4>;
bias-pull-up;
};
};
touch_default_state: touch-default-state {
int-pins {
pins = "gpio61";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
reset-pins {
pins = "gpio60";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
wcnss_pin_a: wcnss-pin-active-state {
wlan-pins {
pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
function = "wlan";
drive-strength = <6>;
bias-pull-down;
};
bt-pins {
pins = "gpio35", "gpio43", "gpio44";
function = "bt";
drive-strength = <2>;
bias-pull-down;
};
};
};
&usb {
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
extcon = <&smbb>, <&usb_id>;
vbus-supply = <&chg_otg>;
hnp-disable;
srp-disable;
adp-disable;
status = "okay";
};
&usb_hs1_phy {
status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
extcon = <&smbb>;
qcom,init-seq = /bits/ 8 <0x1 0x64>;
};
