diff options
Diffstat (limited to 'Bindings/phy')
| -rw-r--r-- | Bindings/phy/berlin-sata-phy.txt | 4 | ||||
| -rw-r--r-- | Bindings/phy/berlin-usb-phy.txt | 16 | ||||
| -rw-r--r-- | Bindings/phy/phy-bindings.txt | 2 | ||||
| -rw-r--r-- | Bindings/phy/phy-miphy28lp.txt | 117 | ||||
| -rw-r--r-- | Bindings/phy/phy-miphy365x.txt | 15 | ||||
| -rw-r--r-- | Bindings/phy/phy-mvebu.txt | 43 | ||||
| -rw-r--r-- | Bindings/phy/phy-stih407-usb.txt | 24 | ||||
| -rw-r--r-- | Bindings/phy/phy-stih41x-usb.txt | 24 | ||||
| -rw-r--r-- | Bindings/phy/qcom-dwc3-usb-phy.txt | 39 | ||||
| -rw-r--r-- | Bindings/phy/rcar-gen2-phy.txt | 51 | ||||
| -rw-r--r-- | Bindings/phy/rockchip-usb-phy.txt | 37 | ||||
| -rw-r--r-- | Bindings/phy/samsung-phy.txt | 15 |
12 files changed, 375 insertions, 12 deletions
diff --git a/Bindings/phy/berlin-sata-phy.txt b/Bindings/phy/berlin-sata-phy.txt index 88f8c23384c0..c0155f842f62 100644 --- a/Bindings/phy/berlin-sata-phy.txt +++ b/Bindings/phy/berlin-sata-phy.txt @@ -2,7 +2,9 @@ Berlin SATA PHY --------------- Required properties: -- compatible: should be "marvell,berlin2q-sata-phy" +- compatible: should be one of + "marvell,berlin2-sata-phy" + "marvell,berlin2q-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - phy-cells: from the generic PHY bindings, must be 1 diff --git a/Bindings/phy/berlin-usb-phy.txt b/Bindings/phy/berlin-usb-phy.txt new file mode 100644 index 000000000000..be33780f668e --- /dev/null +++ b/Bindings/phy/berlin-usb-phy.txt @@ -0,0 +1,16 @@ +* Marvell Berlin USB PHY + +Required properties: +- compatible: "marvell,berlin2-usb-phy" or "marvell,berlin2cd-usb-phy" +- reg: base address and length of the registers +- #phys-cells: should be 0 +- resets: reference to the reset controller + +Example: + + usb-phy@f774000 { + compatible = "marvell,berlin2-usb-phy"; + reg = <0xf774000 0x128>; + #phy-cells = <0>; + resets = <&chip 0x104 14>; + }; diff --git a/Bindings/phy/phy-bindings.txt b/Bindings/phy/phy-bindings.txt index 2aa1840200ed..1293c321754c 100644 --- a/Bindings/phy/phy-bindings.txt +++ b/Bindings/phy/phy-bindings.txt @@ -27,7 +27,7 @@ phys: phy { }; That node describes an IP block (PHY provider) that implements 2 different PHYs. -In order to differentiate between these 2 PHYs, an additonal specifier should be +In order to differentiate between these 2 PHYs, an additional specifier should be given while trying to get a reference to it. PHY user node diff --git a/Bindings/phy/phy-miphy28lp.txt b/Bindings/phy/phy-miphy28lp.txt new file mode 100644 index 000000000000..89caa885d08c --- /dev/null +++ b/Bindings/phy/phy-miphy28lp.txt @@ -0,0 +1,117 @@ +STMicroelectronics STi MIPHY28LP PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA, PCIe or USB3. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy28lp-phy". +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe or USB3 mode setting bits. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI + - PHY_TYPE_USB3 +- reg : Address and length of the register set for the device. +- reg-names : The names of the register addresses corresponding to the registers + filled in "reg". It can also contain the offset of the system configuration + registers used as glue-logic to setup the device for SATA/PCIe or USB3 + devices. +- st,syscfg : Offset of the parent configuration register. +- resets : phandle to the parent reset controller. +- reset-names : Associated name must be "miphy-sw-rst". + +Optional properties (port (child) node): +- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This + is not available in all the MiPHY. For example, for STiH407, only the + MiPHY0 has this bit. +- st,osc-force-ext : to select the external oscillator. This can change from + different MiPHY inside the same SoC. +- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config + register. +- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive + line). +- st,scc-on : enable ssc to reduce effects of EMI (only for sata or PCIe). +- st,tx-impedance-comp : to compensate tx impedance avoiding out of range values. + +example: + + miphy28lp_phy: miphy28lp@9b22000 { + compatible = "st,miphy28lp-phy"; + st,syscfg = <&syscfg_core>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@9b22000 { + reg = <0x9b22000 0xff>, + <0x9b09000 0xff>, + <0x9b04000 0xff>; + reg-names = "sata-up", + "pcie-up", + "pipew"; + + st,syscfg = <0x114 0x818 0xe0 0xec>; + #phy-cells = <1>; + st,osc-rdy; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY0_SOFTRESET>; + }; + + phy_port1: port@9b2a000 { + reg = <0x9b2a000 0xff>, + <0x9b19000 0xff>, + <0x9b14000 0xff>; + reg-names = "sata-up", + "pcie-up", + "pipew"; + + st,syscfg = <0x118 0x81c 0xe4 0xf0>; + + #phy-cells = <1>; + st,osc-force-ext; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY1_SOFTRESET>; + }; + + phy_port2: port@8f95000 { + reg = <0x8f95000 0xff>, + <0x8f90000 0xff>; + reg-names = "pipew", + "usb3-up"; + + st,syscfg = <0x11c 0x820>; + + #phy-cells = <1>; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY2_SOFTRESET>; + }; + }; + + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the miphy device node and an index +specifying which configuration to use, as described in phy-bindings.txt. + +example: + sata0: sata@9b20000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; + +Macro definitions for the supported miphy configuration can be found in: + +include/dt-bindings/phy/phy.h diff --git a/Bindings/phy/phy-miphy365x.txt b/Bindings/phy/phy-miphy365x.txt index 42c880886cf7..9802d5d911aa 100644 --- a/Bindings/phy/phy-miphy365x.txt +++ b/Bindings/phy/phy-miphy365x.txt @@ -6,8 +6,10 @@ for SATA and PCIe. Required properties (controller (parent) node): - compatible : Should be "st,miphy365x-phy" -- st,syscfg : Should be a phandle of the system configuration register group - which contain the SATA, PCIe mode setting bits +- st,syscfg : Phandle / integer array property. Phandle of sysconfig group + containing the miphy registers and integer array should contain + an entry for each port sub-node, specifying the control + register offset inside the sysconfig group. Required nodes : A sub-node is required for each channel the controller provides. Address range information including the usual @@ -26,7 +28,6 @@ Required properties (port (child) node): registers filled in "reg": - sata: For SATA devices - pcie: For PCIe devices - - syscfg: To specify the syscfg based config register Optional properties (port (child) node): - st,sata-gen : Generation of locally attached SATA IP. Expected values @@ -39,20 +40,20 @@ Example: miphy365x_phy: miphy365x@fe382000 { compatible = "st,miphy365x-phy"; - st,syscfg = <&syscfg_rear>; + st,syscfg = <&syscfg_rear 0x824 0x828>; #address-cells = <1>; #size-cells = <1>; ranges; phy_port0: port@fe382000 { - reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>; - reg-names = "sata", "pcie", "syscfg"; + reg = <0xfe382000 0x100>, <0xfe394000 0x100>; + reg-names = "sata", "pcie"; #phy-cells = <1>; st,sata-gen = <3>; }; phy_port1: port@fe38a000 { - reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;; + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;; reg-names = "sata", "pcie", "syscfg"; #phy-cells = <1>; st,pcie-tx-pol-inv; diff --git a/Bindings/phy/phy-mvebu.txt b/Bindings/phy/phy-mvebu.txt new file mode 100644 index 000000000000..f95b6260a3b3 --- /dev/null +++ b/Bindings/phy/phy-mvebu.txt @@ -0,0 +1,43 @@ +* Marvell MVEBU SATA PHY + +Power control for the SATA phy found on Marvell MVEBU SoCs. + +This document extends the binding described in phy-bindings.txt + +Required properties : + + - reg : Offset and length of the register set for the SATA device + - compatible : Should be "marvell,mvebu-sata-phy" + - clocks : phandle of clock and specifier that supplies the device + - clock-names : Should be "sata" + +Example: + sata-phy@84000 { + compatible = "marvell,mvebu-sata-phy"; + reg = <0x84000 0x0334>; + clocks = <&gate_clk 15>; + clock-names = "sata"; + #phy-cells = <0>; + status = "ok"; + }; + +Armada 375 USB cluster +---------------------- + +Armada 375 comes with an USB2 host and device controller and an USB3 +controller. The USB cluster control register allows to manage common +features of both USB controllers. + +Required properties: + +- compatible: "marvell,armada-375-usb-cluster" +- reg: Should contain usb cluster register location and length. +- #phy-cells : from the generic phy bindings, must be 1. Possible +values are 1 (USB2), 2 (USB3). + +Example: + usbcluster: usb-cluster@18400 { + compatible = "marvell,armada-375-usb-cluster"; + reg = <0x18400 0x4>; + #phy-cells = <1> + }; diff --git a/Bindings/phy/phy-stih407-usb.txt b/Bindings/phy/phy-stih407-usb.txt new file mode 100644 index 000000000000..de6a706abcdb --- /dev/null +++ b/Bindings/phy/phy-stih407-usb.txt @@ -0,0 +1,24 @@ +ST STiH407 USB PHY controller + +This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3 +host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics. + +Required properties: +- compatible : should be "st,stih407-usb2-phy" +- st,syscfg : phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets +- resets : list of phandle and reset specifier pairs. There should be two entries, one + for the whole phy and one for the port +- reset-names : list of reset signal names. Should be "global" and "port" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + +usb2_picophy0: usbpicophy@f8 { + compatible = "st,stih407-usb2-phy"; + #phy-cells = <0>; + st,syscfg = <&syscfg_core 0x100 0xf4>; + resets = <&softreset STIH407_PICOPHY_SOFTRESET>, + <&picophyreset STIH407_PICOPHY0_RESET>; + reset-names = "global", "port"; +}; diff --git a/Bindings/phy/phy-stih41x-usb.txt b/Bindings/phy/phy-stih41x-usb.txt new file mode 100644 index 000000000000..00944a05ee6b --- /dev/null +++ b/Bindings/phy/phy-stih41x-usb.txt @@ -0,0 +1,24 @@ +STMicroelectronics STiH41x USB PHY binding +------------------------------------------ + +This file contains documentation for the usb phy found in STiH415/6 SoCs from +STMicroelectronics. + +Required properties: +- compatible : should be "st,stih416-usb-phy" or "st,stih415-usb-phy" +- st,syscfg : should be a phandle of the syscfg node +- clock-names : must contain "osc_phy" +- clocks : must contain an entry for each name in clock-names. +See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- #phy-cells : must be 0 for this phy +See: Documentation/devicetree/bindings/phy/phy-bindings.txt + +Example: + +usb2_phy: usb2phy@0 { + compatible = "st,stih416-usb-phy"; + #phy-cell = <0>; + st,syscfg = <&syscfg_rear>; + clocks = <&clk_sysin>; + clock-names = "osc_phy"; +}; diff --git a/Bindings/phy/qcom-dwc3-usb-phy.txt b/Bindings/phy/qcom-dwc3-usb-phy.txt new file mode 100644 index 000000000000..86f2dbe07ed4 --- /dev/null +++ b/Bindings/phy/qcom-dwc3-usb-phy.txt @@ -0,0 +1,39 @@ +Qualcomm DWC3 HS AND SS PHY CONTROLLER +-------------------------------------- + +DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer +controllers. Each DWC3 PHY controller should have its own node. + +Required properties: +- compatible: should contain one of the following: + - "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller + - "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller +- reg: offset and length of the DWC3 PHY controller register set +- #phy-cells: must be zero +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. +- clock-names: Should contain "ref" for the PHY reference clock + +Optional clocks: + "xo" External reference clock + +Example: + phy@100f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + phy@100f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; diff --git a/Bindings/phy/rcar-gen2-phy.txt b/Bindings/phy/rcar-gen2-phy.txt new file mode 100644 index 000000000000..00fc52a034b7 --- /dev/null +++ b/Bindings/phy/rcar-gen2-phy.txt @@ -0,0 +1,51 @@ +* Renesas R-Car generation 2 USB PHY + +This file provides information on what the device node for the R-Car generation +2 USB PHY contains. + +Required properties: +- compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. +- reg: offset and length of the register block. +- #address-cells: number of address cells for the USB channel subnodes, must + be <1>. +- #size-cells: number of size cells for the USB channel subnodes, must be <0>. +- clocks: clock phandle and specifier pair. +- clock-names: string, clock input name, must be "usbhs". + +The USB PHY device tree node should have the subnodes corresponding to the USB +channels. These subnodes must contain the following properties: +- reg: the USB controller selector; see the table below for the values. +- #phy-cells: see phy-bindings.txt in the same directory, must be <1>. + +The phandle's argument in the PHY specifier is the USB controller selector for +the USB channel; see the selector meanings below: + ++-----------+---------------+---------------+ +|\ Selector | | | ++ --------- + 0 | 1 | +| Channel \| | | ++-----------+---------------+---------------+ +| 0 | PCI EHCI/OHCI | HS-USB | +| 2 | PCI EHCI/OHCI | xHCI | ++-----------+---------------+---------------+ + +Example (Lager board): + + usb-phy@e6590100 { + compatible = "renesas,usb-phy-r8a7790"; + reg = <0 0xe6590100 0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; + clock-names = "usbhs"; + + usb-channel@0 { + reg = <0>; + #phy-cells = <1>; + }; + usb-channel@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; diff --git a/Bindings/phy/rockchip-usb-phy.txt b/Bindings/phy/rockchip-usb-phy.txt new file mode 100644 index 000000000000..826454ac43bb --- /dev/null +++ b/Bindings/phy/rockchip-usb-phy.txt @@ -0,0 +1,37 @@ +ROCKCHIP USB2 PHY + +Required properties: + - compatible: rockchip,rk3288-usb-phy + - rockchip,grf : phandle to the syscon managing the "general + register files" + - #address-cells: should be 1 + - #size-cells: should be 0 + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes +required properties: +- #phy-cells: should be 0 +- reg: PHY configure reg address offset in GRF + "0x320" - for PHY attach to OTG controller + "0x334" - for PHY attach to HOST0 controller + "0x348" - for PHY attach to HOST1 controller + +Optional Properties: +- clocks : phandle + clock specifier for the phy clocks +- clock-names: string, clock name, must be "phyclk" + +Example: + +usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <0>; + + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + }; +}; diff --git a/Bindings/phy/samsung-phy.txt b/Bindings/phy/samsung-phy.txt index 7a6feea2a48b..91e38cfe1f8f 100644 --- a/Bindings/phy/samsung-phy.txt +++ b/Bindings/phy/samsung-phy.txt @@ -3,8 +3,8 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY Required properties: - compatible : should be "samsung,s5pv210-mipi-video-phy"; -- reg : offset and length of the MIPI DPHY register set; - #phy-cells : from the generic phy bindings, must be 1; +- syscon - phandle to the PMU system controller; For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in the PHY specifier identifies the PHY and its meaning is as follows: @@ -17,8 +17,11 @@ Samsung EXYNOS SoC series Display Port PHY ------------------------------------------------- Required properties: -- compatible : should be "samsung,exynos5250-dp-video-phy"; -- reg : offset and length of the Display Port PHY register set; +- compatible : should be one of the following supported values: + - "samsung,exynos5250-dp-video-phy" + - "samsung,exynos5420-dp-video-phy" +- samsung,pmu-syscon: phandle for PMU system controller interface, used to + control pmu registers for power isolation. - #phy-cells : from the generic PHY bindings, must be 0; Samsung S5P/EXYNOS SoC series USB PHY @@ -125,6 +128,7 @@ Required properties: - compatible : Should be set to one of the following supported values: - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC, - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC. + - "samsung,exynos7-usbdrd-phy" - for exynos7 SoC. - reg : Register offset and length of USB DRD PHY register set; - clocks: Clock IDs array as required by the controller - clock-names: names of clocks correseponding to IDs in the clock property; @@ -135,6 +139,11 @@ Required properties: PHY operations, associated by phy name. It is used to determine bit values for clock settings register. For Exynos5420 this is given as 'sclk_usbphy30' in CMU. + - optional clocks: Exynos7 SoC has now following additional + gate clocks available: + - phy_pipe: for PIPE3 phy + - phy_utmi: for UTMI+ phy + - itp: for ITP generation - samsung,pmu-syscon: phandle for PMU system controller interface, used to control pmu registers for power isolation. - #phy-cells : from the generic PHY bindings, must be 1; |