diff options
Diffstat (limited to 'Bindings/regulator/regulator.yaml')
-rw-r--r-- | Bindings/regulator/regulator.yaml | 22 |
1 files changed, 11 insertions, 11 deletions
diff --git a/Bindings/regulator/regulator.yaml b/Bindings/regulator/regulator.yaml index 53b81d8a2d41..e158c2d3d3f9 100644 --- a/Bindings/regulator/regulator.yaml +++ b/Bindings/regulator/regulator.yaml @@ -13,7 +13,7 @@ maintainers: properties: regulator-name: description: A string used as a descriptive name for regulator outputs - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string regulator-min-microvolt: description: smallest voltage consumers may set @@ -23,7 +23,7 @@ properties: regulator-microvolt-offset: description: Offset applied to voltages to compensate for voltage drops - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 regulator-min-microamp: description: smallest current consumers may set @@ -59,7 +59,7 @@ properties: description: ramp delay for regulator(in uV/us) For hardware which supports disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 regulator-enable-ramp-delay: description: The time taken, in microseconds, for the supply rail to @@ -68,7 +68,7 @@ properties: required due to the combination of internal ramping of the regulator itself, and board design issues such as trace capacitance and load on the supply. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 regulator-settling-time-us: description: Settling time, in microseconds, for voltage change if regulator @@ -95,7 +95,7 @@ properties: description: initial operating mode. The set of possible operating modes depends on the capabilities of every hardware so each device binding documentation explains which values the regulator supports. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 regulator-allowed-modes: description: list of operating modes that software is allowed to configure @@ -103,12 +103,12 @@ properties: The set of possible operating modes depends on the capabilities of every hardware so each device binding document explains which values the regulator supports. - $ref: "/schemas/types.yaml#/definitions/uint32-array" + $ref: /schemas/types.yaml#/definitions/uint32-array regulator-system-load: description: Load in uA present on regulator that is not captured by any consumer request. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 regulator-pull-down: description: Enable pull down resistor when the regulator is disabled. @@ -206,14 +206,14 @@ properties: 0: Disable active discharge. 1: Enable active discharge. Absence of this property will leave configuration to default. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 1] regulator-coupled-with: description: Regulators with which the regulator is coupled. The linkage is 2-way - all coupled regulators should be linked with each other. A regulator should not be coupled with its supplier. - $ref: "/schemas/types.yaml#/definitions/phandle-array" + $ref: /schemas/types.yaml#/definitions/phandle-array items: maxItems: 1 @@ -221,7 +221,7 @@ properties: description: Array of maximum spread between voltages of coupled regulators in microvolts, each value in the array relates to the corresponding couple specified by the regulator-coupled-with property. - $ref: "/schemas/types.yaml#/definitions/uint32-array" + $ref: /schemas/types.yaml#/definitions/uint32-array regulator-max-step-microvolt: description: Maximum difference between current and target voltages @@ -269,7 +269,7 @@ patternProperties: of possible operating modes depends on the capabilities of every hardware so the valid modes are documented on each regulator device tree binding document. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 additionalProperties: false |