diff options
Diffstat (limited to 'Bindings/usb/snps,dwc3.yaml')
| -rw-r--r-- | Bindings/usb/snps,dwc3.yaml | 332 |
1 files changed, 332 insertions, 0 deletions
diff --git a/Bindings/usb/snps,dwc3.yaml b/Bindings/usb/snps,dwc3.yaml new file mode 100644 index 000000000000..2247da77eac1 --- /dev/null +++ b/Bindings/usb/snps,dwc3.yaml @@ -0,0 +1,332 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/snps,dwc3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare USB3 Controller + +maintainers: + - Felipe Balbi <balbi@kernel.org> + +description: + This is usually a subnode to DWC3 glue to which it is connected, but can also + be presented as a standalone DT node with an optional vendor-specific + compatible string. + +allOf: + - $ref: usb-drd.yaml# + - if: + properties: + dr_mode: + const: peripheral + + required: + - dr_mode + then: + $ref: usb.yaml# + else: + $ref: usb-xhci.yaml# + +properties: + compatible: + contains: + oneOf: + - const: snps,dwc3 + - const: synopsys,dwc3 + deprecated: true + + interrupts: + description: + It's either a single common DWC3 interrupt (dwc_usb3) or individual + interrupts for the host, gadget and DRD modes. + minItems: 1 + maxItems: 3 + + interrupt-names: + minItems: 1 + maxItems: 3 + oneOf: + - const: dwc_usb3 + - items: + enum: [host, peripheral, otg] + + clocks: + description: + In general the core supports three types of clocks. bus_early is a + SoC Bus Clock (AHB/AXI/Native). ref generates ITP when the UTMI/ULPI + PHY is suspended. suspend clocks a small part of the USB3 core when + SS PHY in P3. But particular cases may differ from that having less + or more clock sources with another names. + + clock-names: + contains: + anyOf: + - enum: [bus_early, ref, suspend] + - true + + usb-phy: + minItems: 1 + items: + - description: USB2/HS PHY + - description: USB3/SS PHY + + phys: + minItems: 1 + items: + - description: USB2/HS PHY + - description: USB3/SS PHY + + phy-names: + minItems: 1 + items: + - const: usb2-phy + - const: usb3-phy + + resets: + minItems: 1 + + snps,usb2-lpm-disable: + description: Indicate if we don't want to enable USB2 HW LPM + type: boolean + + snps,usb3_lpm_capable: + description: Determines if platform is USB3 LPM capable + type: boolean + + snps,dis-start-transfer-quirk: + description: + When set, disable isoc START TRANSFER command failure SW work-around + for DWC_usb31 version 1.70a-ea06 and prior. + type: boolean + + snps,disable_scramble_quirk: + description: + True when SW should disable data scrambling. Only really useful for FPGA + builds. + type: boolean + + snps,has-lpm-erratum: + description: True when DWC3 was configured with LPM Erratum enabled + type: boolean + + snps,lpm-nyet-threshold: + description: LPM NYET threshold + $ref: /schemas/types.yaml#/definitions/uint8 + + snps,u2exit_lfps_quirk: + description: Set if we want to enable u2exit lfps quirk + type: boolean + + snps,u2ss_inp3_quirk: + description: Set if we enable P3 OK for U2/SS Inactive quirk + type: boolean + + snps,req_p1p2p3_quirk: + description: + When set, the core will always request for P1/P2/P3 transition sequence. + type: boolean + + snps,del_p1p2p3_quirk: + description: + When set core will delay P1/P2/P3 until a certain amount of 8B10B errors + occur. + type: boolean + + snps,del_phy_power_chg_quirk: + description: When set core will delay PHY power change from P0 to P1/P2/P3. + type: boolean + + snps,lfps_filter_quirk: + description: When set core will filter LFPS reception. + type: boolean + + snps,rx_detect_poll_quirk: + description: + when set core will disable a 400us delay to start Polling LFPS after + RX.Detect. + type: boolean + + snps,tx_de_emphasis_quirk: + description: When set core will set Tx de-emphasis value + type: boolean + + snps,tx_de_emphasis: + description: + The value driven to the PHY is controlled by the LTSSM during USB3 + Compliance mode. + $ref: /schemas/types.yaml#/definitions/uint8 + enum: + - 0 # -6dB de-emphasis + - 1 # -3.5dB de-emphasis + - 2 # No de-emphasis + + snps,dis_u3_susphy_quirk: + description: When set core will disable USB3 suspend phy + type: boolean + + snps,dis_u2_susphy_quirk: + description: When set core will disable USB2 suspend phy + type: boolean + + snps,dis_enblslpm_quirk: + description: + When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal + to the PHY. + type: boolean + + snps,dis-u1-entry-quirk: + description: Set if link entering into U1 needs to be disabled + type: boolean + + snps,dis-u2-entry-quirk: + description: Set if link entering into U2 needs to be disabled + type: boolean + + snps,dis_rxdet_inp3_quirk: + description: + When set core will disable receiver detection in PHY P3 power state. + type: boolean + + snps,dis-u2-freeclk-exists-quirk: + description: + When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2 + PHY doesn't provide a free-running PHY clock. + type: boolean + + snps,dis-del-phy-power-chg-quirk: + description: + When set core will change PHY power from P0 to P1/P2/P3 without delay. + type: boolean + + snps,dis-tx-ipgap-linecheck-quirk: + description: When set, disable u2mac linestate check during HS transmit + type: boolean + + snps,parkmode-disable-ss-quirk: + description: + When set, all SuperSpeed bus instances in park mode are disabled. + type: boolean + + snps,dis_metastability_quirk: + description: + When set, disable metastability workaround. CAUTION! Use only if you are + absolutely sure of it. + type: boolean + + snps,dis-split-quirk: + description: + When set, change the way URBs are handled by the driver. Needed to + avoid -EPROTO errors with usbhid on some devices (Hikey 970). + type: boolean + + snps,is-utmi-l1-suspend: + description: + True when DWC3 asserts output signal utmi_l1_suspend_n, false when + asserts utmi_sleep_n. + type: boolean + + snps,hird-threshold: + description: HIRD threshold + $ref: /schemas/types.yaml#/definitions/uint8 + + snps,hsphy_interface: + description: + High-Speed PHY interface selection between UTMI+ and ULPI when the + DWC_USB3_HSPHY_INTERFACE has value 3. + $ref: /schemas/types.yaml#/definitions/uint8 + enum: [utmi, ulpi] + + snps,quirk-frame-length-adjustment: + description: + Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame + length adjustment when the fladj_30mhz_sdbnd signal is invalid or + incorrect. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 0x3f + + snps,rx-thr-num-pkt-prd: + description: + Periodic ESS RX packet threshold count (host mode only). Set this and + snps,rx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31 + programming guide section 1.2.4) to enable periodic ESS RX threshold. + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 16 + + snps,rx-max-burst-prd: + description: + Max periodic ESS RX burst size (host mode only). Set this and + snps,rx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31 + programming guide section 1.2.4) to enable periodic ESS RX threshold. + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 16 + + snps,tx-thr-num-pkt-prd: + description: + Periodic ESS TX packet threshold count (host mode only). Set this and + snps,tx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31 + programming guide section 1.2.3) to enable periodic ESS TX threshold. + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 16 + + snps,tx-max-burst-prd: + description: + Max periodic ESS TX burst size (host mode only). Set this and + snps,tx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31 + programming guide section 1.2.3) to enable periodic ESS TX threshold. + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 16 + + tx-fifo-resize: + description: Determines if the FIFO *has* to be reallocated + deprecated: true + type: boolean + + snps,incr-burst-type-adjustment: + description: + Value for INCR burst type of GSBUSCFG0 register, undefined length INCR + burst type enable and INCRx type. A single value means INCRX burst mode + enabled. If more than one value specified, undefined length INCR burst + type will be enabled with burst lengths utilized up to the maximum + of the values passed in this property. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + uniqueItems: true + items: + enum: [1, 4, 8, 16, 32, 64, 128, 256] + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + usb@4a030000 { + compatible = "snps,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4>; + usb-phy = <&usb2_phy>, <&usb3_phy>; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + }; + - | + usb@4a000000 { + compatible = "snps,dwc3"; + reg = <0x4a000000 0xcfff>; + interrupts = <0 92 4>; + clocks = <&clk 1>, <&clk 2>, <&clk 3>; + clock-names = "bus_early", "ref", "suspend"; + phys = <&usb2_phy>, <&usb3_phy>; + phy-names = "usb2-phy", "usb3-phy"; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + }; +... |