diff options
Diffstat (limited to 'hostapd/hostapd.conf')
| -rw-r--r-- | hostapd/hostapd.conf | 115 |
1 files changed, 100 insertions, 15 deletions
diff --git a/hostapd/hostapd.conf b/hostapd/hostapd.conf index 9e81e9e98683..a0071f7d82c4 100644 --- a/hostapd/hostapd.conf +++ b/hostapd/hostapd.conf @@ -127,7 +127,9 @@ ssid=test # Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g, # ad = IEEE 802.11ad (60 GHz); a/g options are used with IEEE 802.11n, too, to -# specify band) +# specify band). When using ACS (see channel parameter), a special value "any" +# can be used to indicate that any support band can be used. This special case +# is currently supported only with drivers with which offloaded ACS is used. # Default: IEEE 802.11b hw_mode=g @@ -170,8 +172,11 @@ channel=1 # Channel list restriction. This option allows hostapd to select one of the # provided channels when a channel should be automatically selected. -# Default: not set (allow any enabled channel to be selected) +# Channel list can be provided as range using hyphen ('-') or individual +# channels can be specified by space (' ') seperated values +# Default: all channels allowed in selected hw_mode #chanlist=100 104 108 112 116 +#chanlist=1 6 11-13 # Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) beacon_int=100 @@ -275,8 +280,9 @@ ignore_broadcast_ssid=0 # (data0 is the highest priority queue) # parameters: # aifs: AIFS (default 2) -# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023) -# cwmax: cwMax (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023); cwMax >= cwMin +# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191, +# 16383, 32767) +# cwmax: cwMax (same values as cwMin, cwMax >= cwMin) # burst: maximum length (in milliseconds with precision of up to 0.1 ms) for # bursting # @@ -337,8 +343,9 @@ ignore_broadcast_ssid=0 # note - txop_limit is in units of 32microseconds # note - acm is admission control mandatory flag. 0 = admission control not # required, 1 = mandatory -# note - here cwMin and cmMax are in exponent form. the actual cw value used -# will be (2^n)-1 where n is the value given here +# note - Here cwMin and cmMax are in exponent form. The actual cw value used +# will be (2^n)-1 where n is the value given here. The allowed range for these +# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin. # wmm_enabled=1 # @@ -575,14 +582,16 @@ wmm_ac_vo_acm=0 # 0 = Not supported (default) # 1 = Supported # -# Compressed Steering Number of Beamformer Antennas Supported: [BF-ANTENNA-2] +# Compressed Steering Number of Beamformer Antennas Supported: +# [BF-ANTENNA-2] [BF-ANTENNA-3] [BF-ANTENNA-4] # Beamformee's capability indicating the maximum number of beamformer # antennas the beamformee can support when sending compressed beamforming # feedback # If SU beamformer capable, set to maximum value minus 1 # else reserved (default) # -# Number of Sounding Dimensions: [SOUNDING-DIMENSION-2] +# Number of Sounding Dimensions: +# [SOUNDING-DIMENSION-2] [SOUNDING-DIMENSION-3] [SOUNDING-DIMENSION-4] # Beamformer's capability indicating the maximum value of the NUM_STS parameter # in the TXVECTOR of a VHT NDP # If SU beamformer capable, set to maximum value minus 1 @@ -593,11 +602,6 @@ wmm_ac_vo_acm=0 # 0 = Not supported or sent by Non-AP STA (default) # 1 = Supported # -# MU Beamformee Capable: [MU-BEAMFORMEE] -# Indicates support for operation as an MU beamformee -# 0 = Not supported or sent by AP (default) -# 1 = Supported -# # VHT TXOP PS: [VHT-TXOP-PS] # Indicates whether or not the AP supports VHT TXOP Power Save Mode # or whether or not the STA is in VHT TXOP Power Save mode @@ -764,6 +768,12 @@ eap_server=0 # 2 = check all CRLs in the certificate path #check_crl=1 +# TLS Session Lifetime in seconds +# This can be used to allow TLS sessions to be cached and resumed with an +# abbreviated handshake when using EAP-TLS/TTLS/PEAP. +# (default: 0 = session caching and resumption disabled) +#tls_session_lifetime=3600 + # Cached OCSP stapling response (DER encoded) # If set, this file is sent as a certificate status response by the EAP server # if the EAP peer requests certificate status in the ClientHello message. @@ -787,7 +797,7 @@ eap_server=0 # is in DSA parameters format, it will be automatically converted into DH # params. This parameter is required if anonymous EAP-FAST is used. # You can generate DH parameters file with OpenSSL, e.g., -# "openssl dhparam -out /etc/hostapd.dh.pem 1024" +# "openssl dhparam -out /etc/hostapd.dh.pem 2048" #dh_file=/etc/hostapd.dh.pem # OpenSSL cipher string @@ -1247,6 +1257,11 @@ own_ip_addr=127.0.0.1 # 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived #pmk_r1_push=1 +# Whether to enable FT-over-DS +# 0 = FT-over-DS disabled +# 1 = FT-over-DS enabled (default) +#ft_over_ds=1 + ##### Neighbor table ########################################################## # Maximum number of entries kept in AP table (either for neigbor table or for # detecting Overlapping Legacy BSS Condition). The oldest entry will be @@ -1264,6 +1279,43 @@ own_ip_addr=127.0.0.1 # default: 60 #ap_table_expiration_time=3600 +# Maximum number of stations to track on the operating channel +# This can be used to detect dualband capable stations before they have +# associated, e.g., to provide guidance on which colocated BSS to use. +# Default: 0 (disabled) +#track_sta_max_num=100 + +# Maximum age of a station tracking entry in seconds +# Default: 180 +#track_sta_max_age=180 + +# Do not reply to group-addressed Probe Request from a station that was seen on +# another radio. +# Default: Disabled +# +# This can be used with enabled track_sta_max_num configuration on another +# interface controlled by the same hostapd process to restrict Probe Request +# frame handling from replying to group-addressed Probe Request frames from a +# station that has been detected to be capable of operating on another band, +# e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when +# the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. +# +# Note: Enabling this can cause connectivity issues and increase latency for +# discovering the AP. +#no_probe_resp_if_seen_on=wlan1 + +# Reject authentication from a station that was seen on another radio. +# Default: Disabled +# +# This can be used with enabled track_sta_max_num configuration on another +# interface controlled by the same hostapd process to reject authentication +# attempts from a station that has been detected to be capable of operating on +# another band, e.g., to try to reduce likelihood of the station selecting a +# 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. +# +# Note: Enabling this can cause connectivity issues and increase latency for +# connecting with the AP. +#no_auth_if_seen_on=wlan1 ##### Wi-Fi Protected Setup (WPS) ############################################# @@ -1430,7 +1482,7 @@ own_ip_addr=127.0.0.1 # 12-digit, all-numeric code that identifies the consumer package. #upc=123456789012 -# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band) +# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band, ad = 60 GHz) # This value should be set according to RF band(s) supported by the AP if # hw_mode is not set. For dual band dual concurrent devices, this needs to be # set to ag to allow both RF bands to be advertized. @@ -1490,6 +1542,13 @@ own_ip_addr=127.0.0.1 # 1 = enabled #proxy_arp=1 +# IPv6 Neighbor Advertisement multicast-to-unicast conversion +# This can be used with Proxy ARP to allow multicast NAs to be forwarded to +# associated STAs using link layer unicast delivery. +# 0 = disabled (default) +# 1 = enabled +#na_mcast_to_ucast=0 + ##### IEEE 802.11u-2011 ####################################################### # Enable Interworking service @@ -1738,6 +1797,32 @@ own_ip_addr=127.0.0.1 # #osu_server_uri=... +##### Fast Session Transfer (FST) support ##################################### +# +# The options in this section are only available when the build configuration +# option CONFIG_FST is set while compiling hostapd. They allow this interface +# to be a part of FST setup. +# +# FST is the transfer of a session from a channel to another channel, in the +# same or different frequency bands. +# +# For detals, see IEEE Std 802.11ad-2012. + +# Identifier of an FST Group the interface belongs to. +#fst_group_id=bond0 + +# Interface priority within the FST Group. +# Announcing a higher priority for an interface means declaring it more +# preferable for FST switch. +# fst_priority is in 1..255 range with 1 being the lowest priority. +#fst_priority=100 + +# Default LLT value for this interface in milliseconds. The value used in case +# no value provided during session setup. Default is 50 ms. +# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2 +# Transitioning between states). +#fst_llt=100 + ##### TESTING OPTIONS ######################################################### # # The options in this section are only available when the build configuration |