diff options
Diffstat (limited to 'src/arm/bcm47094-dlink-dir-890l.dts')
-rw-r--r-- | src/arm/bcm47094-dlink-dir-890l.dts | 211 |
1 files changed, 0 insertions, 211 deletions
diff --git a/src/arm/bcm47094-dlink-dir-890l.dts b/src/arm/bcm47094-dlink-dir-890l.dts deleted file mode 100644 index d945a20b06e0..000000000000 --- a/src/arm/bcm47094-dlink-dir-890l.dts +++ /dev/null @@ -1,211 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/* - * Device tree for D-Link DIR-890L - * D-Link calls this board "WRGAC36" - * this router has the same looks and form factor as D-Link DIR-885L. - * - * Some differences from DIR-885L include a separate USB2 port, separate LEDs - * for USB2 and USB3, a separate VCC supply for the USB2 slot and no - * router/extender switch is mounted (there is an empty mount point on the - * PCB) so this device is a pure router. Also the LAN ports are in the right - * order. - * - * Based on the device tree for DIR-885L - * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com> - * Copyright (C) 2022 Linus Walleij - */ - -/dts-v1/; - -#include "bcm47094.dtsi" -#include "bcm5301x-nand-cs0-bch1.dtsi" - -/ { - compatible = "dlink,dir-890l", "brcm,bcm47094", "brcm,bcm4708"; - model = "D-Link DIR-890L"; - - chosen { - bootargs = "console=ttyS0,115200 earlycon"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x00000000 0x08000000>, - <0x88000000 0x08000000>; - }; - - leds { - /* - * LED information is derived from the boot log which - * conveniently lists all the LEDs. - */ - compatible = "gpio-leds"; - - led-power-white { - label = "bcm53xx:white:power"; - gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>; - linux,default-trigger = "default-on"; - }; - - led-wan-white { - label = "bcm53xx:white:wan"; - gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>; - }; - - led-power-amber { - label = "bcm53xx:amber:power"; - gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; - }; - - led-wan-amber { - label = "bcm53xx:amber:wan"; - gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; - }; - - led-usb3-white { - label = "bcm53xx:white:usb3"; - gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>; - trigger-sources = <&xhci_port1>; - linux,default-trigger = "usbport"; - }; - - led-usb2-white { - label = "bcm53xx:white:usb2"; - gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>; - trigger-sources = <&ohci_port1>, <&ehci_port1>; - linux,default-trigger = "usbport"; - }; - - led-2ghz { - label = "bcm53xx:white:2ghz"; - gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; - }; - - led-5ghz { - label = "bcm53xx:white:5ghz"; - gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - - button-wps { - label = "WPS"; - linux,code = <KEY_WPS_BUTTON>; - gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>; - }; - - /* Called "factory reset" in the vendor dmesg */ - button-restart { - label = "Reset"; - linux,code = <KEY_RESTART>; - gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; - }; - }; - - /* - * The flash memory is memory mapped at 0x1e000000-0x1fffffff - * 64KB blocks; total size 2MB, same that can be - * found attached to the spi_nor SPI controller. - */ - nvram@1e1f0000 { - compatible = "brcm,nvram"; - reg = <0x1e1f0000 0x00010000>; - - et0macaddr: et0macaddr { - }; - }; -}; - -&gmac2 { - /* - * The NVRAM curiously does not contain a MAC address - * for et2 so since that is the only ethernet interface - * actually in use on the platform, we use this et0 MAC - * address for et2. - */ - nvmem-cells = <&et0macaddr>; - nvmem-cell-names = "mac-address"; -}; - -&spi_nor { - status = "okay"; -}; - -&nandcs { - /* Spansion S34ML01G2, 128MB with 128KB erase blocks */ - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - /* - * This is called "nflash" in the vendor kernel with - * "upgrade" and "rootfs" (probably using OpenWrt - * splitpart). We call it "firmware" like standard tools - * assume. The CFE loader contains incorrect information - * about TRX partitions, ignore this, there are no TRX - * partitions: this device uses SEAMA. - */ - firmware@0 { - label = "firmware"; - reg = <0x00000000 0x08000000>; - }; - }; -}; - -&usb2 { - vcc-gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>; -}; - -&usb3 { - vcc-gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>; -}; - -&usb3_phy { - status = "okay"; -}; - -&srab { - status = "okay"; - - ports { - port@0 { - reg = <0>; - label = "lan1"; - }; - - port@1 { - reg = <1>; - label = "lan2"; - }; - - port@2 { - reg = <2>; - label = "lan3"; - }; - - port@3 { - reg = <3>; - label = "lan4"; - }; - - port@4 { - reg = <4>; - label = "wan"; - }; - - port@8 { - reg = <8>; - label = "cpu"; - ethernet = <&gmac2>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; |