1 files changed, 0 insertions, 172 deletions
diff --git a/src/arm/ste-nomadik-s8815.dts b/src/arm/ste-nomadik-s8815.dts
deleted file mode 100644
index f16314ffbf4b..000000000000
--- a/src/arm/ste-nomadik-s8815.dts
+++ /dev/null
@@ -1,172 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree for the ST-Ericsson Nomadik S8815 board
- * Produced by Calao Systems
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "ste-nomadik-stn8815.dtsi"
-
-/ {
-	model = "Calao Systems USB-S8815";
-	compatible = "calaosystems,usb-s8815";
-
-	chosen {
-		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
-	};
-
-	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-	};
-
-	gpio3: gpio@101e7000 {
-		/* This hog will bias the MMC/SD card detect line */
-		mmcsd-gpio {
-			gpio-hog;
-			gpios = <16 0x0>;
-			output-low;
-			line-name = "card detect bias";
-		};
-	};
-
-	src@101e0000 {
-		/* These chrystal drivers are not used on this board */
-		disable-sxtalo;
-		disable-mxtalo;
-	};
-
-	pinctrl {
-		/* Hog CD pins */
-		pinctrl-names = "default";
-		pinctrl-0 = <&cd_default_mode>;
-
-		uart0 {
-			/* Only use RX/TX pins */
-			uart0_s8815_mode: uart0_mux {
-				u0_default_mux {
-					function = "u0";
-					groups = "u0txrx_a_1";
-				};
-			};
-		};
-		mmcsd-cd {
-			cd_default_mode: cd_default {
-				cd_default_cfg1 {
-					/* CD input GPIO */
-					pins = "GPIO111_H21";
-					ste,input = <0>;
-				};
-				cd_default_cfg2 {
-					/* CD GPIO biasing */
-					pins = "GPIO112_J21";
-					ste,output = <0>;
-				};
-			};
-		};
-		gpioi2c {
-			gpioi2c_default_mode: gpioi2c_default {
-				gpioi2c_default_cfg {
-					pins = "GPIO73_C21", "GPIO74_C20";
-					ste,input = <0>;
-				};
-			};
-		};
-		user-led {
-			user_led_default_mode: user_led_default {
-				user_led_default_cfg {
-					pins = "GPIO2_C5";
-					ste,output = <1>;
-				};
-			};
-		};
-		user-button {
-			user_button_default_mode: user_button_default {
-				user_button_default_cfg {
-					pins = "GPIO3_A4";
-					ste,input = <0>;
-				};
-			};
-		};
-	};
-
-	/* Ethernet */
-	external-bus@34000000 {
-		compatible = "simple-bus";
-		reg = <0x34000000 0x1000000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0x34000000 0x1000000>;
-		ethernet@300 {
-			compatible = "smsc,lan91c111";
-			reg = <0x300 0x0fd00>;
-			interrupt-parent = <&gpio3>;
-			interrupts = <8 IRQ_TYPE_EDGE_RISING>;
-		};
-	};
-
-	i2c1 {
-		lis3lv02dl@1d {
-			/* Accelerometer */
-			compatible = "st,lis3lv02dl-accel";
-			reg = <0x1d>;
-		};
-	};
-
-	/* GPIO I2C connected to the USB portions of the STw4811 only */
-	gpio-i2c {
-		compatible = "i2c-gpio";
-		gpios = <&gpio2 10 0>, /* sda */
-			<&gpio2 9 0>; /* scl */
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpioi2c_default_mode>;
-
-		stw4811@2d {
-			   compatible = "st,stw4811-usb";
-			   reg = <0x2d>;
-		};
-	};
-
-
-	amba {
-		/* Activate RXTX on UART 0 */
-		uart0: uart@101fd000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_s8815_mode>;
-			status = "okay";
-		};
-		/* Configure card detect for the uSD slot */
-		mmc@101f6000 {
-			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	/* The user LED on the board is set up to be used for heartbeat */
-	leds {
-		compatible = "gpio-leds";
-		user-led {
-			label = "user_led";
-			gpios = <&gpio0 2 0x1>;
-			default-state = "off";
-			linux,default-trigger = "heartbeat";
-			pinctrl-names = "default";
-			pinctrl-0 = <&user_led_default_mode>;
-		};
-	};
-
-	/* User key mapped in as "escape" */
-	gpio-keys {
-		compatible = "gpio-keys";
-		user-button {
-			label = "user_button";
-			gpios = <&gpio0 3 0x1>;
-			linux,code = <1>; /* KEY_ESC */
-			wakeup-source;
-			pinctrl-names = "default";
-			pinctrl-0 = <&user_button_default_mode>;
-		};
-	};
-};