diff options
Diffstat (limited to 'src/arm64/qcom/msm8916-longcheer-l8150.dts')
| -rw-r--r-- | src/arm64/qcom/msm8916-longcheer-l8150.dts | 145 |
1 files changed, 21 insertions, 124 deletions
diff --git a/src/arm64/qcom/msm8916-longcheer-l8150.dts b/src/arm64/qcom/msm8916-longcheer-l8150.dts index f1dd625e1822..97262b8519b3 100644 --- a/src/arm64/qcom/msm8916-longcheer-l8150.dts +++ b/src/arm64/qcom/msm8916-longcheer-l8150.dts @@ -14,7 +14,9 @@ chassis-type = "handset"; aliases { - serial0 = &blsp1_uart2; + mmc0 = &sdhc_1; /* eMMC */ + mmc1 = &sdhc_2; /* SD card */ + serial0 = &blsp_uart2; }; chosen { @@ -41,7 +43,7 @@ button-volume-up { label = "Volume Up"; - gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; linux,code = <KEY_VOLUMEUP>; }; }; @@ -53,7 +55,7 @@ regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - gpio = <&msmgpio 17 GPIO_ACTIVE_HIGH>; + gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-names = "default"; @@ -62,8 +64,8 @@ flash-led-controller { compatible = "sgmicro,sgm3140"; - flash-gpios = <&msmgpio 31 GPIO_ACTIVE_HIGH>; - enable-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>; + flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; + enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&camera_flash_default>; @@ -122,7 +124,7 @@ * to the BMC156. However, there are two pads next to the chip * that can be shorted to make it work if needed. * - * interrupt-parent = <&msmgpio>; + * interrupt-parent = <&tlmm>; * interrupts = <116 IRQ_TYPE_EDGE_RISING>; */ @@ -141,7 +143,7 @@ compatible = "bosch,bmc156_magn"; reg = <0x12>; - interrupt-parent = <&msmgpio>; + interrupt-parent = <&tlmm>; interrupts = <113 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; @@ -156,7 +158,7 @@ reg = <0x23>; proximity-near-level = <75>; - interrupt-parent = <&msmgpio>; + interrupt-parent = <&tlmm>; interrupts = <115 IRQ_TYPE_EDGE_FALLING>; pinctrl-names = "default"; @@ -170,7 +172,7 @@ compatible = "bosch,bmg160"; reg = <0x68>; - interrupt-parent = <&msmgpio>; + interrupt-parent = <&tlmm>; interrupts = <23 IRQ_TYPE_EDGE_RISING>, <22 IRQ_TYPE_EDGE_RISING>; @@ -191,7 +193,7 @@ #address-cells = <1>; #size-cells = <0>; - interrupt-parent = <&msmgpio>; + interrupt-parent = <&tlmm>; interrupts = <13 IRQ_TYPE_EDGE_FALLING>; vdd-supply = <®_ctp>; @@ -214,7 +216,7 @@ }; }; -&blsp1_uart2 { +&blsp_uart2 { status = "okay"; }; @@ -223,6 +225,13 @@ linux,code = <KEY_VOLUMEDOWN>; }; +&pm8916_rpm_regulators { + pm8916_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; +}; + &pm8916_usbin { status = "okay"; }; @@ -233,19 +242,10 @@ &sdhc_1 { status = "okay"; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; - pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; }; &sdhc_2 { status = "okay"; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; - pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; - non-removable; }; @@ -267,110 +267,7 @@ compatible = "qcom,wcn3620"; }; -&smd_rpm_regulators { - vdd_l1_l2_l3-supply = <&pm8916_s3>; - vdd_l4_l5_l6-supply = <&pm8916_s4>; - vdd_l7-supply = <&pm8916_s4>; - - s3 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1300000>; - }; - - s4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2100000>; - }; - - l1 { - regulator-min-microvolt = <1225000>; - regulator-max-microvolt = <1225000>; - }; - - l2 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - }; - - l4 { - regulator-min-microvolt = <2050000>; - regulator-max-microvolt = <2050000>; - }; - - l5 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - l6 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - l7 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - l8 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2900000>; - }; - - l9 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - l10 { - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <2800000>; - }; - - l11 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2950000>; - regulator-allow-set-load; - regulator-system-load = <200000>; - }; - - l12 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2950000>; - }; - - l13 { - regulator-min-microvolt = <3075000>; - regulator-max-microvolt = <3075000>; - }; - - l14 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - - l15 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - - l16 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - - l17 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - }; - - l18 { - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <2700000>; - }; -}; - -&msmgpio { +&tlmm { accel_int_default: accel-int-default-state { pins = "gpio116"; function = "gpio"; |