aboutsummaryrefslogtreecommitdiff
path: root/sys/dev/vge
Commit message (Collapse)AuthorAgeFilesLines
* MFC r200696,200740,200756,200758-200759,200972Pyun YongHyeon2010-01-093-26/+244
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | r200696: Add rudimentary WOL support. While I'm here remove enabling busmastering/memory address in resume path. Bus driver will handle that. r200740: Swap VGE_TXQTIMER and VGE_RXQTIMER register definition. Pending timer for Tx queue is at 0x3E. r200756: Correct fragment bit definition in comments. r200758: VT6130 datasheet was wrong. If VT6130 receive a jumbo frame the controller will split the jumbo frame into multiple RX buffers. However it seems the hardware always dma the frame to 8 bytes boundary for the split frames. Only the first part of the fragment can have 4 byte alignment and subsequent buffers should be 8 bytes aligned. Change RX buffer the alignment requirement to 8 bytes from 4 bytes. r200759: Disable jumbo frame support for PCIe VT6130/VT6132 controllers. Quite contrary to VT6130 datasheet which says it supports up to 8K jumbo frame, VT6130 does not seem to send jumbo frame that is larger than 4K in length. Trying to send a frame that is larger than 4K cause TX MAC hang. Even though it's possible to allow 4K jumbo frame for VT6130, I think it's meaningless to allow 4K jumbo frame. I'm not sure VT6132 also has the same limitation but I guess it uses the same MAC of VT6130. r200972: Remove wrong assertion. Notes: svn path=/stable/7/; revision=201874
* MFC r200638:Pyun YongHyeon2010-01-093-80/+103
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement interrupt moderation scheme supported by VT61xx controllers. TX/RX interrupt mitigation is controlled by VGE_TXSUPPTHR and VGE_RXSUPPTHR register. These registers suppress generation of interrupts until the programmed frames counter equals to the registers. VT61xx also supports interrupt hold off timer register. If this interrupt hold off timer is active all interrupts would be disabled until the timer reaches to 0. The timer value is reloaded whenever VGE_ISR register written. The timer resolution is about 20us. Previously vge(4) used single shot timer to reduce Tx completion interrupts. This required VGE_CRS1 register access in Tx start/completion handler to rearm new timeout value and it did not show satisfactory result(more than 50k interrupts under load). Rx interrupts was not moderated at all such that vge(4) used to generate too many interrupts which in turn made polling(4) better approach under high network load. This change activates all interrupt moderation mechanism and initial values were tuned to generate interrupt less than 8k per second. That number of interrupts wouldn't add additional packet latencies compared to polling(4). These interrupt parameters could be changed with sysctl. dev.vge.%d.int_holdoff dev.vge.%d.rx_coal_pkt dev.vge.%d.tx_coal_pkt Interface has be brought down and up again before change take effect. With interrupt moderation there is no more need to loop in interrupt handler. This loop always added one more register access. While I'm here remove dead code which tried to implement subset of interrupt moderation. Notes: svn path=/stable/7/; revision=201869
* MFC r200616-200617,200635,200639,200644Pyun YongHyeon2010-01-092-20/+8
| | | | | | | | | | | | | | | | | | | | | | | | | r200616: Add new flag VGE_FLAG_SUSPENDED to mark suspended state and remove suspended member in softc. r200617: Add "Velocity" to probe message which will make it clearer which ethernet controller was recognized. VIA consistently calls "Velocity" family for gigabit ethernet controllers. For fast ethernet controllers they uses "Rhine" family(vr(4) controllers)) and vr(4) already shows "Rhine" in probe message. r200635: Remove unused VGE_ETHER_ALIGN definition. r200639: Actually clear interrupts. Writing 0 has no effect. r200644: Remove unused member variable of softc. Notes: svn path=/stable/7/; revision=201867
* MFC 200615:Pyun YongHyeon2010-01-093-3/+322
| | | | | | | | Add hardware MAC statistics support. This statistics could be extracted from dev.vge.%d.stats sysctl node. Notes: svn path=/stable/7/; revision=201865
* MFC r200551-200552,200555,200558,200609,200613Pyun YongHyeon2010-01-091-70/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | r200551: Whenever link state change interrupt is raised, vge_tick() is called and vge(4) used to drive auto-negotiation timer(mii_tick) in vge_tick(). Therefore the mii_tick was not called for every hz such that auto-negotiation complete was never handled in vge(4). Use mii_pollstat to extract current negotiated speed/duplex instead of mii_tick. The latter is valid only for auto-negotiation case. While I'm here change the confusing function name vge_tick() to vge_link_statchg(). r200552: Report media change result to caller instead of returning success without regard to the result. r200555: Don't report current link status if interface is not UP. If interface is not UP, the current link status wouldn't reflect the negotiated status. r200558: Tell upper layer vge(4) supports long frames. This should be done after ether_ifattach(), as ether_ifattach() initializes it with ETHER_HDR_LEN. While I'm here remove setting if_mtu, it's already handled in ether_ifattach(). r200609: All vge(4) controllers support RX/TX checksum offloading for VLAN tagged frames so add checksum offloading capabilities. Also add missing VLAN hardware tagging control in ioctl handler and let upper stack know current VLAN capabilities. r200613: Rewrite RX filter setup and simplify code. Now promiscuous mode and multicast handling is performed in single function, vge_rxfilter(). Notes: svn path=/stable/7/; revision=201861
* MFC r200538,200540-200541,200543,200545,200548Pyun YongHyeon2010-01-082-82/+114
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | r200538: Introduce vge_flags member in softc. The vge_flags member will record device specific bits. Remove vge_link and use vge_flags. While here, move clearing link state before mii_mediachg() as mii_mediachg() may affect link state. r200540: Save PHY address by reading VGE_MIICFG register. For PCIe controllers(VT613x), we assume the PHY address is 1. Use the saved PHY address in MII register access routines and remove accessing VGE_MIICFG register. While I'm here save PCI express capability register which will be used in near future. r200541: Add MSI support for VT613x controllers. r200543: Increase output queue size from 64 to 255. r200545: We don't have to reload EEPROM in vge_reset(). Because vge_reset() is called in vge_init_lock(), vge(4) always used to reload EEPROM. Also add more comment why vge(4) clears VGE_CHIPCFG0_PACPI bit. While I'm here add missing new line in vge_reset(). r200548: Sort function prototyes. Notes: svn path=/stable/7/; revision=201841
* MFC r200526-200527,200529,200531-200533,200536Pyun YongHyeon2010-01-083-236/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | r200526: Use PCIR_BAR instead of hard-coded value. r200527: Fix typo in register definition. r200529: Clear VGE_TXDESC_Q bit for transmitted frames. The VGE_TXDESC_Q bit seems to work like a tag that indicates 'not list end' of queued frames. Without having a VGE_TXDESC_Q bit indicates 'list end'. So the last frame of multiple queued frames has no VGE_TXDESC_Q bit. The hardware has peculiar behavior for VGE_TXDESC_Q bit handling. If the VGE_TXDESC_Q bit of descriptor was set the controller would fetch next descriptor. However if next descriptor's OWN bit was cleared but VGE_TXDESC_Q was set, it could confuse controller. Clearing VGE_TXDESC_Q bit for transmitted frames ensure correct behavior. r200531: Use ANSI function definations. r200532: Remove unnecessary return statement. r200533: s/u_intXX_t/uintXX_t/g r200536: style(9). Notes: svn path=/stable/7/; revision=201839
* MFC r200525:Pyun YongHyeon2010-01-083-688/+836
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Overhaul bus_dma(9) usage and fix various things. o Separate TX/RX buffer DMA tag from TX/RX descriptor ring DMA tag. o Separate RX buffer DMA tag from common buffer DMA tag. RX DMA tag has different restriction compared to TX DMA tag. o Add 40bit DMA address support. o Adjust TX/RX descriptor ring alignment to 64 bytes from 256 bytes as documented in datasheet. o Added check to ensure TX/RX ring reside within a 4GB boundary. Since TX/RX ring shares the same high address register they should have the same high address. o TX/RX side bus_dmamap_load_mbuf_sg(9) support. o Add lock assertion to vge_setmulti(). o Add RX spare DMA map to recover from DMA map load failure. o Add optimized RX buffer handler, vge_discard_rxbuf which is activated when vge(4) sees bad frames. o Don't blindly update VGE_RXDESC_RESIDUECNT register. Datasheet says the register should be updated only when number of available RX descriptors are multiple of 4. o Use __NO_STRICT_ALIGNMENT instead of defining VGE_FIXUP_RX which is only set for i386 architecture. Previously vge(4) also performed expensive copy operation to align IP header on amd64. This change should give RX performance boost on amd64 architecture. o Don't reinitialize controller if driver is already running. This should reduce number of link state flipping. o Since vge(4) drops a driver lock before passing received frame to upper layer, make sure vge(4) is still running after re-acquiring driver lock. o Add second argument count to vge_rxeof(). The argument will limit number of packets could be processed in RX handler. o Rearrange vge_rxeof() not to allocate RX buffer if received frame was bad packet. o Removed if_printf that prints DMA map failure. This type of message shouldn't be used in fast path of driver. o Reduce number of allowed TX buffer fragments to 6 from 7. A TX descriptor allows 7 fragments of a frame. However the CMZ field of descriptor has just 3bits and the controller wants to see fragment + 1 in the field. So if we have 7 fragments the field value would be 0 which seems to cause unexpected results under certain conditions. This change should fix occasional TX hang observed on vge(4). o Simplify vge_stat_locked() and add number of available TX descriptor check. o vge(4) controllers lack padding short frames. Make sure to fill zero for the padded bytes. This closes unintended information disclosure. o Don't set VGE_TDCTL_JUMBO flag. Datasheet is not clear whether this bit should be set by driver or write-back status bit after transmission. At least vendor's driver does not set this bit so remove it. Without this bit vge(4) still can send jumbo frames. o Don't start driver when vge(4) know there are not enough RX buffers. o Remove volatile keyword in RX descriptor structure. This should be handled by bus_dma(9). o Collapse two 16bits member of TX/RX descriptor into single 32bits member. o Reduce number of RX descriptors to 252 from 256. The VGE_RXDESCNUM is 16bits register but only lower 8bits are valid. So the maximum number of RX descriptors would be 255. However the number of should be multiple of 4 as controller wants to update 4 RX descriptors at a time. This limits the maximum number of RX descriptor to be 252. PR: kern/141276, kern/141414 Notes: svn path=/stable/7/; revision=201834
* MFC r200519-200522Pyun YongHyeon2010-01-081-15/+14
| | | | | | | | | | | | | | | | | r200519: Remove register keyword. r200520: Prefer device_printf(9) to printf(9). r200521: Fix spelling in comment. r200522: Prefer bus_alloc_resource_any(9) to bus_alloc_resource(9). Notes: svn path=/stable/7/; revision=201827
* MFC r198987,199414,199543,200422Pyun YongHyeon2010-01-082-103/+92
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Partial merge r198987: Use device_printf() and if_printf() instead of printf() with an explicit unit number and remove 'unit' members from softc. Partial merge r199414: Use the bus_*() routines rather than bus_space_*() for register operations. r199543: Several fixes to this driver: - Overhaul the locking to avoid recursion and add missing locking in a few places. - Don't schedule a task to call vge_start() from contexts that are safe to call vge_start() directly. Just invoke the routine directly instead (this is what all of the other NIC drivers I am familiar with do). Note that vge(4) does not use an interrupt filter handler which is the primary reason some other drivers use tasks. - Add a new private timer to drive the watchdog timer instead of using if_watchdog and if_timer. - Fixup detach by calling ether_ifdetach() before stopping the interface. r200422: Remove driver lock assertion in MII register access. This change was made in r199543 to remove MTX_RECURSE. These routines can be called in device attach phase(e.g. mii_phy_probe()) so checking assertion here is not right as caller does not hold a driver lock. Notes: svn path=/stable/7/; revision=201824
* MFC r184908:Pyun YongHyeon2009-01-121-7/+9
| | | | | | | | | | | | Fix Rx/Tx checksum offload ioctl handling. Now checksum offload can be controlled by ifconfig(8). Note, VLAN hardware tagging controls still lacks required handler but it requires more driver cleanups so I didn't touch that part. PR: kern/128766 Notes: svn path=/stable/7/; revision=187078
* MFC: Fix function prototype for device_shutdown method.Pyun YongHyeon2008-03-131-2/+4
| | | | Notes: svn path=/stable/7/; revision=177136
* Catch up the rest of the drivers with the ether_vlan_mtap modifications.Christian S.J. Peron2007-03-041-1/+1
| | | | | | | | | | | | | If these drivers are setting M_VLANTAG because they are stripping the layer 2 802.1Q headers, then they need to be re-inserting them so any bpf(4) peers can properly decode them. It should be noted that this is compiled tested only. MFC after: 3 weeks Notes: svn path=/head/; revision=167190
* o break newbus api: add a new argument of type driver_filter_t toPaolo Pisati2007-02-231-1/+1
| | | | | | | | | | | | | | | | bus_setup_intr() o add an int return code to all fast handlers o retire INTR_FAST/IH_FAST For more info: http://docs.freebsd.org/cgi/getmsg.cgi?fetch=465712+0+current/freebsd-current Reviewed by: many Approved by: re@ Notes: svn path=/head/; revision=166901
* Complete the support for altq(4).Christian Brueffer2007-02-211-1/+3
| | | | | | | | | | Tested by: J.R. Oldroyd Reviewed by: mlaier Approved by: rwatson (mentor) MFC after: 1 week Notes: svn path=/head/; revision=166865
* Fix the hardware VLAN tagging. TX was broken on little-endianRuslan Ermilov2006-11-301-2/+7
| | | | | | | | | | | | | | | | | machines and both TX and RX were broken on big-endian machines. The chip design is crazy -- on RX, it puts the 16-bit VLAN tag in network byte order (big-endian) in the 32-bit little-endian register! Thanks to John Baldwin for helping me document this change! ;-) Tested by: sat (amd64), test program (sparc64) PR: kern/105054 MFC after: 3 days Notes: svn path=/head/; revision=164776
* Remove pre-5.3 compatibility ifdefs.Christian Brueffer2006-11-291-61/+0
| | | | | | | | Approved by: rwatson (mentor) MFC after: 5 days Notes: svn path=/head/; revision=164759
* Move ethernet VLAN tags from mtags to its own mbuf packet header fieldAndre Oppermann2006-09-171-8/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf signifies the presence and validity of its content. Drivers that support hardware VLAN tag stripping fill in the received VLAN tag (containing both vlan and priority information) into the ether_vtag mbuf packet header field: m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */ m->m_flags |= M_VLANTAG; to mark the packet m with the specified VLAN tag. On output the driver should check the mbuf for the M_VLANTAG flag to see if a VLAN tag is present and valid: if (m->m_flags & M_VLANTAG) { ... = m->m_pkthdr.ether_vtag; /* htons()? */ ... pass tag to hardware ... } VLAN tags are stored in host byte order. Byte swapping may be necessary. (Note: This driver conversion was mechanic and did not add or remove any byte swapping in the drivers.) Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag memory allocation have to be done. Reviewed by: thompsa, yar Sponsored by: TCP/IP Optimization Fundraise 2005 Notes: svn path=/head/; revision=162375
* Add locking to vge_ifmedia_upd().Michael Reifenberger2006-09-041-0/+2
| | | | | | | | | | | With this WD-timeouts for vge(4) got reduced signifficantly. Testet on -stable. Submitted by: Oleg Bulyzhin MFC after: 1 day Notes: svn path=/head/; revision=161995
* Do not touch ifp->if_baudrate in miibus aware drivers.Gleb Smirnoff2006-02-141-1/+0
| | | | Notes: svn path=/head/; revision=155671
* - Fix VLAN_INPUT_TAG() macro, so that it doesn't touch mtag inGleb Smirnoff2005-12-181-2/+5
| | | | | | | | | | | | case if memory allocation failed. - Remove fourth argument from VLAN_INPUT_TAG(), that was used incorrectly in almost all drivers. Indicate failure with mbuf value of NULL. In collaboration with: yongari, ru, sam Notes: svn path=/head/; revision=153512
* - Store pointer to the link-level address right in "struct ifnet"Ruslan Ermilov2005-11-111-1/+1
| | | | | | | | | | | | | rather than in ifindex_table[]; all (except one) accesses are through ifp anyway. IF_LLADDR() works faster, and all (except one) ifaddr_byindex() users were converted to use ifp->if_addr. - Stop storing a (pointer to) Ethernet address in "struct arpcom", and drop the IFP2ENADDR() macro; all users have been converted to use IF_LLADDR() instead. Notes: svn path=/head/; revision=152315
* Replace FreeBSD 3.x syntax (controller miibus0) with 4.x syntaxWarner Losh2005-10-221-1/+1
| | | | | | | (device miibus) in time for 7.0 :-) Notes: svn path=/head/; revision=151545
* - Don't pollute opt_global.h with DEVICE_POLLING and introduceGleb Smirnoff2005-10-051-0/+4
| | | | | | | | | | | | opt_device_polling.h - Include opt_device_polling.h into appropriate files. - Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that can be compiled as loadable modules. Reviewed by: bde Notes: svn path=/head/; revision=150968
* Big polling(4) cleanup.Gleb Smirnoff2005-10-011-54/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | o Axe poll in trap. o Axe IFF_POLLING flag from if_flags. o Rework revision 1.21 (Giant removal), in such a way that poll_mtx is not dropped during call to polling handler. This fixes problem with idle polling. o Make registration and deregistration from polling in a functional way, insted of next tick/interrupt. o Obsolete kern.polling.enable. Polling is turned on/off with ifconfig. Detailed kern_poll.c changes: - Remove polling handler flags, introduced in 1.21. The are not needed now. - Forget and do not check if_flags, if_capenable and if_drv_flags. - Call all registered polling handlers unconditionally. - Do not drop poll_mtx, when entering polling handlers. - In ether_poll() NET_LOCK_GIANT prior to locking poll_mtx. - In netisr_poll() axe the block, where polling code asks drivers to unregister. - In netisr_poll() and ether_poll() do polling always, if any handlers are present. - In ether_poll_[de]register() remove a lot of error hiding code. Assert that arguments are correct, instead. - In ether_poll_[de]register() use standard return values in case of error or success. - Introduce poll_switch() that is a sysctl handler for kern.polling.enable. poll_switch() goes through interface list and enabled/disables polling. A message that kern.polling.enable is deprecated is printed. Detailed driver changes: - On attach driver announces IFCAP_POLLING in if_capabilities, but not in if_capenable. - On detach driver calls ether_poll_deregister() if polling is enabled. - In polling handler driver obtains its lock and checks IFF_DRV_RUNNING flag. If there is no, then unlocks and returns. - In ioctl handler driver checks for IFCAP_POLLING flag requested to be set or cleared. Driver first calls ether_poll_[de]register(), then obtains driver lock and [dis/en]ables interrupts. - In interrupt handler driver checks IFCAP_POLLING flag in if_capenable. If present, then returns.This is important to protect from spurious interrupts. Reviewed by: ru, sam, jhb Notes: svn path=/head/; revision=150789
* Make sure that we call if_free(ifp) after bus_teardown_intr. Since weWarner Losh2005-09-191-2/+2
| | | | | | | | | | could get an interrupt after we free the ifp, and the interrupt handler depended on the ifp being still alive, this could, in theory, cause a crash. Eliminate this possibility by moving the if_free to after the bus_teardown_intr() call. Notes: svn path=/head/; revision=150306
* Fix "struct ifnet" leaks when attach() fails in the middle.Ruslan Ermilov2005-09-161-1/+2
| | | | Notes: svn path=/head/; revision=150215
* Propagate rename of IFF_OACTIVE and IFF_RUNNING to IFF_DRV_OACTIVE andRobert Watson2005-08-091-10/+10
| | | | | | | | | | | | | | | | | IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to ifnet.if_drv_flags. Device drivers are now responsible for synchronizing access to these flags, as they are in if_drv_flags. This helps prevent races between the network stack and device driver in maintaining the interface flags field. Many __FreeBSD__ and __FreeBSD_version checks maintained and continued; some less so. Reviewed by: pjd, bz MFC after: 7 days Notes: svn path=/head/; revision=148887
* Modify device drivers supporting multicast addresses to lock if_addr_mtxRobert Watson2005-08-031-0/+2
| | | | | | | | | | | over iteration of their multicast address lists when synchronizing the hardware address filter with the network stack-maintained list. Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca> MFC after: 1 week Notes: svn path=/head/; revision=148654
* Move if_alloc() up so it's before mii_phy_probe().Brooks Davis2005-06-111-6/+7
| | | | Notes: svn path=/head/; revision=147291
* Stop embedding struct ifnet at the top of driver softcs. Instead theBrooks Davis2005-06-102-16/+22
| | | | | | | | | | | | | | | | | | | | | | | struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam Notes: svn path=/head/; revision=147256
* Remove some variables the last commit stopped using so the code compiles.Brooks Davis2005-06-061-2/+0
| | | | Notes: svn path=/head/; revision=147038
* The PCI bus code saves/restores these config registers now.Warner Losh2005-06-052-21/+0
| | | | Notes: svn path=/head/; revision=147027
* Remove bus_{mem,p}io.h and related code for a micro-optimization on i386Yoshihiro Takahashi2005-05-291-2/+0
| | | | | | | | | and amd64. The optimization is a trivial on recent machines. Reviewed by: -arch (imp, marcel, dfr) Notes: svn path=/head/; revision=146734
* Remove the extra EEPROM reload step I added before. vge_reset()Bill Paul2005-04-251-2/+0
| | | | | | | already does this anyway. Notes: svn path=/head/; revision=145537
* Correct the if_link_state_change() logic: when the link went down,Bill Paul2005-04-251-2/+2
| | | | | | | | if_link_state_change() reported link up, and when the link went up, if_link_state_change() reported link down. These should be swapped. Notes: svn path=/head/; revision=145521
* Reading the EEPROM to learn the station address doesn't seem to workBill Paul2005-04-251-0/+11
| | | | | | | | | | | | on boards with VIA gigE controllers that are embedded in VIA chipsets. Presumably, they don't have an external EEPROM and store the MAC address somewhere else. To get around this, force an autoload and read the station address from the RX filter registers instead. This has been tested to work on both embedded and standalone controllers. Notes: svn path=/head/; revision=145520
* Use BUS_PROBE_DEFAULT in preference to 0. Also for vx, returnWarner Losh2005-03-011-1/+1
| | | | | | | | BUS_PROBE_LOW_PRIORITY in stead of ifdef for devices that xl and vx both support so that xl will snarf them on up. Notes: svn path=/head/; revision=142880
* Use if_link_state_change() instead of rt_ifmsg(). Remove include net/route.h.Gleb Smirnoff2005-02-071-9/+4
| | | | | | | Reviewed by: wpaul, sam Notes: svn path=/head/; revision=141474
* Start each of the license/copyright comments with /*-, minor shuffle of linesWarner Losh2005-01-063-3/+3
| | | | Notes: svn path=/head/; revision=139749
* Remove unneeded TX channel wakeup from vge_txeof(). This was putBill Paul2004-09-111-1/+0
| | | | | | | | there for testing and forgotten. It's not really needed, and taking it out saves a register access. Notes: svn path=/head/; revision=135091
* Remove unneeded VGE_UNLOCK() in vge_detach().Bill Paul2004-09-111-1/+0
| | | | Notes: svn path=/head/; revision=135062
* Add device driver support for the VIA Networking TechnologiesBill Paul2004-09-103-0/+3316
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY. The vge driver has been added to GENERIC for i386, pc98 and amd64, but not to sparc or ia64 since I don't have the ability to test it there. The vge(4) driver supports VLANs, checksum offload and jumbo frames. Also added the lge(4) and nge(4) drivers to GENERIC for i386 and pc98 since I was in the neighborhood. There's no reason to leave them out anymore. Notes: svn path=/head/; revision=135048
generated by cgit v1.3 (git 2.53.0) at 2026-05-29 22:29:37 +0000