3 files changed, 49 insertions, 45 deletions
diff --git a/share/man/man4/aacraid.4 b/share/man/man4/aacraid.4
index 3bf683ac40c8..0f64f36c493a 100644
--- a/share/man/man4/aacraid.4
+++ b/share/man/man4/aacraid.4
@@ -1,3 +1,6 @@
+.\"
+.\" SPDX-License-Identifier: BSD-2-Clause
+.\"
 .\" Copyright (c) 2013 Achim Leubner
 .\" All rights reserved.
 .\"
@@ -21,12 +24,12 @@
 .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 .\" SUCH DAMAGE.
-.Dd June 19, 2015
+.Dd September 29, 2025
 .Dt AACRAID 4
 .Os
 .Sh NAME
 .Nm aacraid
-.Nd Adaptec AACRAID Controller driver
+.Nd Adaptec Series 6/7/8 6G and 12G SAS+SATA RAID controller driver
 .Sh SYNOPSIS
 To compile this driver into the kernel,
 place the following lines in your
@@ -78,9 +81,10 @@ Linux-compatible
 interface for the management device will be enabled and will allow
 Linux-based management applications to control the card.
 .Sh HARDWARE
-Controllers supported by the
+The
 .Nm
-driver include:
+driver supports the following
+Adaptec 6G and 12G SAS/SATA RAID controllers:
 .Pp
 .Bl -bullet -compact
 .It
diff --git a/share/man/man4/ice.4 b/share/man/man4/ice.4
index 13ad304a2d5a..c7675e627726 100644
--- a/share/man/man4/ice.4
+++ b/share/man/man4/ice.4
@@ -39,18 +39,28 @@
 .Nm ice
 .Nd Intel Ethernet 800 Series Driver
 .Sh SYNOPSIS
-To compile this driver into the kernel, place the following lines in your
-kernel configuration file:
-.Bd -literal -offset indent
 .Cd device iflib
 .Cd device ice
-.Ed
 .Pp
-To load the driver as a module at boot time, place the following lines in
+In
 .Xr loader.conf 5 :
-.Bd -literal -offset indent
-if_ice_load="YES"
-.Ed
+.Cd if_ice_load
+.Cd hw.ice.enable_health_events
+.Cd hw.ice.irdma
+.Cd hw.ice.irdma_max_msix
+.Cd hw.ice.debug.enable_tx_fc_filter
+.Cd hw.ice.debug.enable_tx_lldp_filter
+.Cd hw.ice.debug.ice_tx_balance_en
+.Pp
+In
+.Xr sysctl.conf 5
+or
+.Xr loader.conf 5 :
+.Cd dev.ice.#.current_speed
+.Cd dev.ice.#.fw_version
+.Cd dev.ice.#.ddp_version
+.Cd dev.ice.#.pba_number
+.Cd dev.ice.#.hw.mac.*
 .Sh DESCRIPTION
 .Ss Features
 The
diff --git a/share/man/man4/umass.4 b/share/man/man4/umass.4
index db4e6f0890f2..8c6b03a3afea 100644
--- a/share/man/man4/umass.4
+++ b/share/man/man4/umass.4
@@ -25,44 +25,44 @@
 .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 .\" SUCH DAMAGE.
 .\"
-.Dd October 2, 2025
+.Dd October 9, 2025
 .Dt UMASS 4
 .Os
 .Sh NAME
 .Nm umass
 .Nd USB Mass Storage Devices driver
 .Sh SYNOPSIS
-To compile this driver into the kernel,
-place the following line in your
-kernel configuration file:
-.Bd -ragged -offset indent
+.Cd "device da"
 .Cd "device scbus"
+.Cd "device pass"
 .Cd "device usb"
 .Cd "device umass"
-.Ed
 .Pp
-Alternatively, to load the driver as a
-module at boot time, place the following line in
+In
 .Xr loader.conf 5 :
-.Bd -literal -offset indent
-umass_load="YES"
-.Ed
+.Cd umass_load
 .Sh DESCRIPTION
 The
 .Nm
 driver provides support for Mass Storage devices that attach to the USB
-port.
+interface.
 .Pp
-To use the
-.Nm
-driver,
+If the appropriate hardware is detected,
+the driver will be loaded automatically by
+.Xr devmatch 8 .
+To load the driver manually at boot time, use the
+.Cm umass_load
+command at the
+.Xr loader 8
+prompt, or add it to
+.Xr loader.conf 5 .
+.Pp
+To use the driver in a custom kernel,
 .Xr usb 4
-and one of
-.Xr uhci 4
-or
-.Xr ohci 4
-or
-.Xr ehci 4
+and at least one of
+.Xr uhci 4 ,
+.Xr ohci 4 ,
+.Xr ehci 4 ,
 or
 .Xr xhci 4
 must be configured in the kernel.
@@ -88,16 +88,8 @@ USB hard disk drives
 USB floppy drives
 .El
 .Sh EXAMPLES
-.Bd -literal -offset indent
-device umass
-device scbus
-device da
-device pass
-.Ed
-.Pp
-Add the
-.Nm
-driver to the kernel.
+Rescan all slots on a multi-slot flash reader,
+where the slots map to separate LUNs on a single SCSI ID:
 .Bd -literal -offset indent
 camcontrol rescan 0:0:0
 camcontrol rescan 0:0:1
@@ -105,8 +97,6 @@ camcontrol rescan 0:0:2
 camcontrol rescan 0:0:3
 .Ed
 .Pp
-Rescan all slots on a multi-slot flash reader, where the slots map to separate
-LUNs on a single SCSI ID.
 Typically only the first slot will be enabled at boot time.
 This assumes that
 the flash reader is the first SCSI bus in the system and has 4 slots.