diff options
Diffstat (limited to 'src/riscv/starfive/jh7100-common.dtsi')
| -rw-r--r-- | src/riscv/starfive/jh7100-common.dtsi | 131 |
1 files changed, 131 insertions, 0 deletions
diff --git a/src/riscv/starfive/jh7100-common.dtsi b/src/riscv/starfive/jh7100-common.dtsi index b93ce351a90f..42fb61c36068 100644 --- a/src/riscv/starfive/jh7100-common.dtsi +++ b/src/riscv/starfive/jh7100-common.dtsi @@ -12,6 +12,8 @@ / { aliases { + mmc0 = &sdio0; + mmc1 = &sdio1; serial0 = &uart3; }; @@ -39,6 +41,35 @@ label = "ack"; }; }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dma-reserved@fa000000 { + reg = <0x0 0xfa000000 0x0 0x1000000>; + no-map; + }; + + linux,dma@107a000000 { + compatible = "shared-dma-pool"; + reg = <0x10 0x7a000000 0x0 0x1000000>; + no-map; + linux,dma-default; + }; + }; + + soc { + dma-ranges = <0x00 0x80000000 0x00 0x80000000 0x00 0x7a000000>, + <0x00 0xfa000000 0x10 0x7a000000 0x00 0x01000000>, + <0x00 0xfb000000 0x00 0xfb000000 0x07 0x85000000>; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + }; }; &gpio { @@ -84,6 +115,78 @@ }; }; + sdio0_pins: sdio0-0 { + clk-pins { + pinmux = <GPIOMUX(54, GPO_SDIO0_PAD_CCLK_OUT, + GPO_ENABLE, GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + }; + sdio-pins { + pinmux = <GPIOMUX(55, GPO_LOW, GPO_DISABLE, + GPI_SDIO0_PAD_CARD_DETECT_N)>, + <GPIOMUX(53, + GPO_SDIO0_PAD_CCMD_OUT, + GPO_SDIO0_PAD_CCMD_OEN, + GPI_SDIO0_PAD_CCMD_IN)>, + <GPIOMUX(49, + GPO_SDIO0_PAD_CDATA_OUT_BIT0, + GPO_SDIO0_PAD_CDATA_OEN_BIT0, + GPI_SDIO0_PAD_CDATA_IN_BIT0)>, + <GPIOMUX(50, + GPO_SDIO0_PAD_CDATA_OUT_BIT1, + GPO_SDIO0_PAD_CDATA_OEN_BIT1, + GPI_SDIO0_PAD_CDATA_IN_BIT1)>, + <GPIOMUX(51, + GPO_SDIO0_PAD_CDATA_OUT_BIT2, + GPO_SDIO0_PAD_CDATA_OEN_BIT2, + GPI_SDIO0_PAD_CDATA_IN_BIT2)>, + <GPIOMUX(52, + GPO_SDIO0_PAD_CDATA_OUT_BIT3, + GPO_SDIO0_PAD_CDATA_OEN_BIT3, + GPI_SDIO0_PAD_CDATA_IN_BIT3)>; + bias-pull-up; + input-enable; + input-schmitt-enable; + }; + }; + + sdio1_pins: sdio1-0 { + clk-pins { + pinmux = <GPIOMUX(33, GPO_SDIO1_PAD_CCLK_OUT, + GPO_ENABLE, GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + }; + sdio-pins { + pinmux = <GPIOMUX(29, + GPO_SDIO1_PAD_CCMD_OUT, + GPO_SDIO1_PAD_CCMD_OEN, + GPI_SDIO1_PAD_CCMD_IN)>, + <GPIOMUX(36, + GPO_SDIO1_PAD_CDATA_OUT_BIT0, + GPO_SDIO1_PAD_CDATA_OEN_BIT0, + GPI_SDIO1_PAD_CDATA_IN_BIT0)>, + <GPIOMUX(30, + GPO_SDIO1_PAD_CDATA_OUT_BIT1, + GPO_SDIO1_PAD_CDATA_OEN_BIT1, + GPI_SDIO1_PAD_CDATA_IN_BIT1)>, + <GPIOMUX(34, + GPO_SDIO1_PAD_CDATA_OUT_BIT2, + GPO_SDIO1_PAD_CDATA_OEN_BIT2, + GPI_SDIO1_PAD_CDATA_IN_BIT2)>, + <GPIOMUX(31, + GPO_SDIO1_PAD_CDATA_OUT_BIT3, + GPO_SDIO1_PAD_CDATA_OEN_BIT3, + GPI_SDIO1_PAD_CDATA_IN_BIT3)>; + bias-pull-up; + input-enable; + input-schmitt-enable; + }; + }; + uart3_pins: uart3-0 { rx-pins { pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE, @@ -154,6 +257,34 @@ clock-frequency = <27000000>; }; +&sdio0 { + broken-cd; + bus-width = <4>; + cap-sd-highspeed; + pinctrl-names = "default"; + pinctrl-0 = <&sdio0_pins>; + status = "okay"; +}; + +&sdio1 { + #address-cells = <1>; + #size-cells = <0>; + bus-width = <4>; + cap-sd-highspeed; + cap-sdio-irq; + cap-power-off-card; + mmc-pwrseq = <&wifi_pwrseq>; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&sdio1_pins>; + status = "okay"; + + wifi@1 { + compatible = "brcm,bcm4329-fmac"; + reg = <1>; + }; +}; + &uart3 { pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>; |