diff options
Diffstat (limited to 'sys/cam/cam.h')
| -rw-r--r-- | sys/cam/cam.h | 237 |
1 files changed, 59 insertions, 178 deletions
diff --git a/sys/cam/cam.h b/sys/cam/cam.h index 09103b6e42df..a7d51db19941 100644 --- a/sys/cam/cam.h +++ b/sys/cam/cam.h @@ -40,10 +40,6 @@ typedef u_int path_id_t; typedef u_int target_id_t; typedef u_int lun_id_t; -typedef union { - u_int64_t lun64; - u_int8_t lun[8]; -} lun64_id_t; #define CAM_XPT_PATH_ID ((path_id_t)~0) #define CAM_BUS_WILDCARD ((path_id_t)~0) @@ -124,184 +120,69 @@ enum { /* CAM Status field values */ typedef enum { - /* CCB request is in progress */ - CAM_REQ_INPROG = 0x00, + CAM_REQ_INPROG, /* CCB request is in progress */ + CAM_REQ_CMP, /* CCB request completed without error */ + CAM_REQ_ABORTED, /* CCB request aborted by the host */ + CAM_UA_ABORT, /* Unable to abort CCB request */ + CAM_REQ_CMP_ERR, /* CCB request completed with an error */ + CAM_BUSY, /* CAM subsystem is busy */ + CAM_REQ_INVALID, /* CCB request was invalid */ + CAM_PATH_INVALID, /* Supplied Path ID is invalid */ + CAM_DEV_NOT_THERE, /* SCSI Device Not Installed/there */ + CAM_UA_TERMIO, /* Unable to terminate I/O CCB request */ + CAM_SEL_TIMEOUT, /* Target Selection Timeout */ + CAM_CMD_TIMEOUT, /* Command timeout */ + CAM_SCSI_STATUS_ERROR, /* SCSI error, look at error code in CCB */ + CAM_MSG_REJECT_REC, /* Message Reject Received */ + CAM_SCSI_BUS_RESET, /* SCSI Bus Reset Sent/Received */ + CAM_UNCOR_PARITY, /* Uncorrectable parity error occurred */ + CAM_AUTOSENSE_FAIL = 0x10,/* Autosense: request sense cmd fail */ + CAM_NO_HBA, /* No HBA Detected error */ + CAM_DATA_RUN_ERR, /* Data Overrun error */ + CAM_UNEXP_BUSFREE, /* Unexpected Bus Free */ + CAM_SEQUENCE_FAIL, /* Target Bus Phase Sequence Failure */ + CAM_CCB_LEN_ERR, /* CCB length supplied is inadequate */ + CAM_PROVIDE_FAIL, /* Unable to provide requested capability */ + CAM_BDR_SENT, /* A SCSI BDR msg was sent to target */ + CAM_REQ_TERMIO, /* CCB request terminated by the host */ + CAM_UNREC_HBA_ERROR, /* Unrecoverable Host Bus Adapter Error */ + CAM_REQ_TOO_BIG, /* The request was too large for this host */ + CAM_REQUEUE_REQ, /* + * This request should be requeued to preserve + * transaction ordering. This typically occurs + * when the SIM recognizes an error that should + * freeze the queue and must place additional + * requests for the target at the sim level + * back into the XPT queue. + */ + CAM_ATA_STATUS_ERROR, /* ATA error, look at error code in CCB */ + CAM_SCSI_IT_NEXUS_LOST, /* Initiator/Target Nexus lost. */ + CAM_SMP_STATUS_ERROR, /* SMP error, look at error code in CCB */ + CAM_IDE = 0x33, /* Initiator Detected Error */ + CAM_RESRC_UNAVAIL, /* Resource Unavailable */ + CAM_UNACKED_EVENT, /* Unacknowledged Event by Host */ + CAM_MESSAGE_RECV, /* Message Received in Host Target Mode */ + CAM_INVALID_CDB, /* Invalid CDB received in Host Target Mode */ + CAM_LUN_INVALID, /* Lun supplied is invalid */ + CAM_TID_INVALID, /* Target ID supplied is invalid */ + CAM_FUNC_NOTAVAIL, /* The requested function is not available */ + CAM_NO_NEXUS, /* Nexus is not established */ + CAM_IID_INVALID, /* The initiator ID is invalid */ + CAM_CDB_RECVD, /* The SCSI CDB has been received */ + CAM_LUN_ALRDY_ENA, /* The LUN is already enabled for target mode */ + CAM_SCSI_BUSY, /* SCSI Bus Busy */ - /* CCB request completed without error */ - CAM_REQ_CMP = 0x01, + CAM_DEV_QFRZN = 0x40, /* The DEV queue is frozen w/this err */ - /* CCB request aborted by the host */ - CAM_REQ_ABORTED = 0x02, + /* Autosense data valid for target */ + CAM_AUTOSNS_VALID = 0x80, + CAM_RELEASE_SIMQ = 0x100,/* SIM ready to take more commands */ + CAM_SIM_QUEUED = 0x200,/* SIM has this command in it's queue */ - /* Unable to abort CCB request */ - CAM_UA_ABORT = 0x03, + CAM_STATUS_MASK = 0x3F, /* Mask bits for just the status # */ - /* CCB request completed with an error */ - CAM_REQ_CMP_ERR = 0x04, - - /* CAM subsystem is busy */ - CAM_BUSY = 0x05, - - /* CCB request was invalid */ - CAM_REQ_INVALID = 0x06, - - /* Supplied Path ID is invalid */ - CAM_PATH_INVALID = 0x07, - - /* SCSI Device Not Installed/there */ - CAM_DEV_NOT_THERE = 0x08, - - /* Unable to terminate I/O CCB request */ - CAM_UA_TERMIO = 0x09, - - /* Target Selection Timeout */ - CAM_SEL_TIMEOUT = 0x0a, - - /* Command timeout */ - CAM_CMD_TIMEOUT = 0x0b, - - /* SCSI error, look at error code in CCB */ - CAM_SCSI_STATUS_ERROR = 0x0c, - - /* Message Reject Received */ - CAM_MSG_REJECT_REC = 0x0d, - - /* SCSI Bus Reset Sent/Received */ - CAM_SCSI_BUS_RESET = 0x0e, - - /* Uncorrectable parity error occurred */ - CAM_UNCOR_PARITY = 0x0f, - - /* Autosense: request sense cmd fail */ - CAM_AUTOSENSE_FAIL = 0x10, - - /* No HBA Detected error */ - CAM_NO_HBA = 0x11, - - /* Data Overrun error */ - CAM_DATA_RUN_ERR = 0x12, - - /* Unexpected Bus Free */ - CAM_UNEXP_BUSFREE = 0x13, - - /* Target Bus Phase Sequence Failure */ - CAM_SEQUENCE_FAIL = 0x14, - - /* CCB length supplied is inadequate */ - CAM_CCB_LEN_ERR = 0x15, - - /* Unable to provide requested capability*/ - CAM_PROVIDE_FAIL = 0x16, - - /* A SCSI BDR msg was sent to target */ - CAM_BDR_SENT = 0x17, - - /* CCB request terminated by the host */ - CAM_REQ_TERMIO = 0x18, - - /* Unrecoverable Host Bus Adapter Error */ - CAM_UNREC_HBA_ERROR = 0x19, - - /* Request was too large for this host */ - CAM_REQ_TOO_BIG = 0x1a, - - /* - * This request should be requeued to preserve - * transaction ordering. This typically occurs - * when the SIM recognizes an error that should - * freeze the queue and must place additional - * requests for the target at the sim level - * back into the XPT queue. - */ - CAM_REQUEUE_REQ = 0x1b, - - /* ATA error, look at error code in CCB */ - CAM_ATA_STATUS_ERROR = 0x1c, - - /* Initiator/Target Nexus lost. */ - CAM_SCSI_IT_NEXUS_LOST = 0x1d, - - /* SMP error, look at error code in CCB */ - CAM_SMP_STATUS_ERROR = 0x1e, - - /* - * Command completed without error but exceeded the soft - * timeout threshold. - */ - CAM_REQ_SOFTTIMEOUT = 0x1f, - - /* - * 0x20 - 0x32 are unassigned - */ - - /* Initiator Detected Error */ - CAM_IDE = 0x33, - - /* Resource Unavailable */ - CAM_RESRC_UNAVAIL = 0x34, - - /* Unacknowledged Event by Host */ - CAM_UNACKED_EVENT = 0x35, - - /* Message Received in Host Target Mode */ - CAM_MESSAGE_RECV = 0x36, - - /* Invalid CDB received in Host Target Mode */ - CAM_INVALID_CDB = 0x37, - - /* Lun supplied is invalid */ - CAM_LUN_INVALID = 0x38, - - /* Target ID supplied is invalid */ - CAM_TID_INVALID = 0x39, - - /* The requested function is not available */ - CAM_FUNC_NOTAVAIL = 0x3a, - - /* Nexus is not established */ - CAM_NO_NEXUS = 0x3b, - - /* The initiator ID is invalid */ - CAM_IID_INVALID = 0x3c, - - /* The SCSI CDB has been received */ - CAM_CDB_RECVD = 0x3d, - - /* The LUN is already enabled for target mode */ - CAM_LUN_ALRDY_ENA = 0x3e, - - /* SCSI Bus Busy */ - CAM_SCSI_BUSY = 0x3f, - - - /* - * Flags - */ - - /* The DEV queue is frozen w/this err */ - CAM_DEV_QFRZN = 0x40, - - /* Autosense data valid for target */ - CAM_AUTOSNS_VALID = 0x80, - - /* SIM ready to take more commands */ - CAM_RELEASE_SIMQ = 0x100, - - /* SIM has this command in it's queue */ - CAM_SIM_QUEUED = 0x200, - - /* Quality of service data is valid */ - CAM_QOS_VALID = 0x400, - - /* Mask bits for just the status # */ - CAM_STATUS_MASK = 0x3F, - - /* - * Target Specific Adjunct Status - */ - - /* sent sense with status */ - CAM_SENT_SENSE = 0x40000000 + /* Target Specific Adjunct Status */ + CAM_SENT_SENSE = 0x40000000 /* sent sense with status */ } cam_status; typedef enum { |